stmbl

#ifdef FB_TX
#error at the moment you can only have one component using the tx channel of the feeback port(res or encm)
#else
#define FB_TX
#endif

COMP(encm);

HAL_PIN(pos) = 0.0;

HAL_PIN(error) = 0;

MEM(uint32_t error_) = 0.0;
MEM(uint8_t menc_buf[10]);

INIT(
  GPIO_InitTypeDef GPIO_InitStruct;
  USART_InitTypeDef USART_InitStruct;
  
  //TX enable
  RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);
  GPIO_InitStruct.GPIO_Pin   = GPIO_Pin_12;
  GPIO_InitStruct.GPIO_Mode  = GPIO_Mode_OUT;
  GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
  GPIO_InitStruct.GPIO_Speed = GPIO_Speed_2MHz;
  GPIO_InitStruct.GPIO_PuPd  = GPIO_PuPd_NOPULL;
  GPIO_Init(GPIOB, &GPIO_InitStruct);

  RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);
  RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOB, ENABLE);

  //USART TX
  GPIO_PinAFConfig(GPIOB, GPIO_PinSource10, GPIO_AF_USART3);
  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_10;
  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_AF;
  GPIO_InitStruct.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_UP ;
  GPIO_Init(GPIOB, &GPIO_InitStruct);

  //USART RX
  GPIO_PinAFConfig(GPIOB, GPIO_PinSource11, GPIO_AF_USART3);
  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_11;
  GPIO_Init(GPIOB, &GPIO_InitStruct);

  USART_InitStruct.USART_BaudRate = 2500000;
  USART_InitStruct.USART_WordLength = USART_WordLength_8b;
  USART_InitStruct.USART_StopBits = USART_StopBits_1;
  USART_InitStruct.USART_Parity = USART_Parity_No;
  USART_InitStruct.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
  USART_InitStruct.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
  USART_Init(USART3, &USART_InitStruct);

  /* Enable the USART */
  USART_Cmd(USART3, ENABLE);

  // Clock Enable
  RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA1, ENABLE);

  // DMA-Disable
  DMA_Cmd(DMA1_Stream1, DISABLE);
  DMA_DeInit(DMA1_Stream1);

  // DMA2-Config
  DMA_InitStructure.DMA_Channel = DMA_Channel_4;
  DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)&(USART3->DR);
  DMA_InitStructure.DMA_Memory0BaseAddr = (uint32_t)&menc_buf;
  DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralToMemory;
  DMA_InitStructure.DMA_BufferSize = 9;
  DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
  DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
  DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
  DMA_InitStructure.DMA_MemoryDataSize = DMA_PeripheralDataSize_Byte;
  DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;
  DMA_InitStructure.DMA_Priority = DMA_Priority_High;
  DMA_InitStructure.DMA_FIFOMode = DMA_FIFOMode_Disable;
  DMA_InitStructure.DMA_FIFOThreshold = DMA_FIFOThreshold_HalfFull;
  DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single;
  DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;
  DMA_Init(DMA1_Stream1, &DMA_InitStructure);

  USART_DMACmd(USART3, USART_DMAReq_Rx, ENABLE);
);

RT(
   uint32_t tpos;

   if(menc_buf[0] == 0x32 && ((menc_buf[0] ^ menc_buf[1] ^ menc_buf[2] ^ menc_buf[3] ^ menc_buf[4] ^ menc_buf[5] ^ menc_buf[6] ^ menc_buf[7] ^ menc_buf[8]) == 0)){
      tpos = ((menc_buf[2] & 0x80) >> 7) + menc_buf[3]*2 + menc_buf[4]*512;
      PIN(pos) = (tpos * M_PI * 2.0 / 131072.0) - M_PI;
      PIN(error) = 0.0;
   }else{
      error_++;
      PIN(error) = error_;
   }

   GPIO_SetBits(GPIOB,GPIO_Pin_12);//tx enable
   USART_SendData(USART3, 0x32);
   while (USART_GetFlagStatus(USART3, USART_FLAG_TC) == RESET);
   GPIO_ResetBits(GPIOB,GPIO_Pin_12);//tx disable
   DMA_Cmd(DMA1_Stream1, DISABLE);
   DMA_ClearFlag(DMA1_Stream1, DMA_FLAG_TCIF1);
   DMA_Cmd(DMA1_Stream1, ENABLE);
);

ENDCOMP;