stmbl

#ifdef CMD_RX
#error you can only have one command component
#else
#define CMD_RX
#endif

HAL_COMP(enc_cmd);

HAL_PIN(res) = 2048.0;
HAL_PIN(pos) = 0.0;

MEM(int e_res) = 0.0;

RT_INIT(
  GPIO_InitTypeDef GPIO_InitStructure;
  TIM_ICInitTypeDef TIM_ICInitStructure;
  TIM_ICInitStructure.TIM_Channel = TIM_Channel_1 | TIM_Channel_2;
  TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_BothEdge;
  TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI;
  TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1;
  TIM_ICInitStructure.TIM_ICFilter = 0xF;
  TIM_ICInit(ENC0_TIM, &TIM_ICInitStructure);

  /***************** port 0, quadrature or step/dir *********************/
  e_res = (int)PIN(res);
  if(e_res < 1){
	  e_res = 1;
  }
  // enable clocks
  RCC_APB2PeriphClockCmd(ENC0_TIM_RCC, ENABLE);

  // pin af -> tim
  GPIO_PinAFConfig(ENC0_A_PORT, ENC0_A_PIN_SOURCE, ENC0_A_AF_SOURCE);//ch1
  GPIO_PinAFConfig(ENC0_B_PORT, ENC0_B_PIN_SOURCE, ENC0_B_AF_SOURCE);//ch2

  // enc res / turn
  TIM_SetAutoreload(ENC0_TIM, e_res - 1);

  // quad
  TIM_Cmd(ENC0_TIM, DISABLE);
  TIM1->CR1 |= TIM_CR1_DIR;
  GPIO_InitStructure.GPIO_Pin = ENC0_A_PIN | ENC0_B_PIN;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
  GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
  GPIO_Init(ENC0_A_PORT, &GPIO_InitStructure);
  TIM_EncoderInterfaceConfig(ENC0_TIM, TIM_EncoderMode_TI12, TIM_ICPolarity_Rising, TIM_ICPolarity_Rising);
  TIM_Cmd(ENC0_TIM, ENABLE);
);

RT_DEINIT(
   TIM_Cmd(ENC0_TIM, DISABLE);
   TIM_DeInit(ENC0_TIM);
   RCC_APB2PeriphClockCmd(ENC0_TIM_RCC, DISABLE);
   GPIO_InitStructure.GPIO_Pin = ENC0_A_PIN | ENC0_B_PIN;
   GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
   GPIO_InitStructure.GPIO_Speed = GPIO_Speed_2MHz;
   GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
   GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL;
   GPIO_Init(ENC0_A_PORT, &GPIO_InitStructure);
);

RT(
  float p = 0.0;


  int res = (int)PIN(res);
  if(res < 1){
	  res = 1;
  }

  p = mod(TIM_GetCounter(ENC0_TIM) * 2.0f * M_PI / (float)e_res);
  PIN(pos) = p;
  if(e_res != res){
    e_res = res;
    TIM_SetAutoreload(ENC0_TIM, e_res - 1);
  }
);

ENDCOMP;

//http://stackoverflow.com/questions/32947972/stm32-how-to-make-pulse-count-up-down-with-timer
// #include "mbed.h"
// #include "stm32f4xx.h"
// #include "stm32f4xx_hal_tim_ex.h"
//
// TIM_HandleTypeDef timer;
// TIM_Encoder_InitTypeDef encoder;
//
// //direction to PA_9 -- step to PA_8
//
// int main(){
//      GPIO_InitTypeDef GPIO_InitStruct;
//         __TIM1_CLK_ENABLE();
//         __GPIOA_CLK_ENABLE();
//         GPIO_InitStruct.Pin = GPIO_PIN_8 | GPIO_PIN_9;
//         GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
//         GPIO_InitStruct.Pull = GPIO_PULLDOWN;
//         GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
//         GPIO_InitStruct.Alternate = GPIO_AF1_TIM1;
//         HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
//
//     timer.Instance = TIM1;
//     timer.Init.Period = 0xffff;
//     timer.Init.Prescaler = 1;
//     timer.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
//     timer.Init.CounterMode = TIM_COUNTERMODE_UP;
//
//
//     encoder.EncoderMode = TIM_ENCODERMODE_TI1;
//     encoder.IC1Filter = 0x0f;
//     encoder.IC1Polarity = TIM_INPUTCHANNELPOLARITY_RISING; //step signal
//     encoder.IC1Prescaler = TIM_ICPSC_DIV1;
//     encoder.IC1Selection = TIM_ICSELECTION_DIRECTTI;
//
//     encoder.IC2Filter = 0x0f;
//     encoder.IC2Polarity = TIM_INPUTCHANNELPOLARITY_BOTHEDGE;  //check direction
//     encoder.IC2Prescaler = TIM_ICPSC_DIV1;
//     encoder.IC2Selection = TIM_ICSELECTION_INDIRECTTI;
//
//     HAL_TIM_Encoder_Init(&timer, &encoder);
//     HAL_TIM_Encoder_Start(&timer,TIM_CHANNEL_1);
//
//
//     TIM1->EGR = 1;           // Generate an update event
//     TIM1->CR1 = 1;           // Enable the counter
//
//
//  while (1) {
//         int16_t count1;
//         count1=TIM1->CNT;
//
//         printf("%d\r\n", count1);
//         wait(1.0);
//
//  };
// }