Loading files
This file is pinned to the selected release. Download the original to open it in your design tool.
ab0f3a7ddThis file is pinned to the selected release. Download the original to open it in your design tool.
---
doc_id: MTC-REQ-001
title: MotionCore requirements
project: MotionCore
doc_type: Requirements
version: "0.4"
status: Draft
date: '2026-09-25'
author: Amish Chadha
license: CERN-OHL-S-2.0
revisions:
- version: "0.1"
date: '2026-09-25'
author: Amish Chadha
change: Initial scaffold
- version: "0.2"
date: '2026-09-25'
author: Amish Chadha
change: First measurable requirements for TRL 2, with status against the concept estimates
- version: "0.3"
date: '2026-09-25'
author: Amish Chadha
change: TRL 3. R2 heavy case relaxed to 350 W and R14 redefined to the MotionCore kit without the motor (MTC-DDR-001, adopted for TRL 3 pending Amish's review); status column from MTC-CAL-001
- version: "0.4"
date: '2026-09-25'
author: Amish Chadha
change: Recommendations accepted by Amish (DDR-002). R1 upper bound 58 to 60 V; R12 mass limit 1.5 to 2.0 kg; status from MTC-CAL-001 v0.2
---
# MotionCore requirements
These requirements are checked by calculation in MTC-CAL-001 v0.2. Four targets have changed since TRL 2, all decided by Amish on 2026-09-25 (MTC-DDR-001 and MTC-DDR-002): the heavy case in R2 is 350 W instead of 500 W; R14 covers the MotionCore kit without the reference motor; the upper bound of R1 is 60 V instead of 58 V, so that CellGuard's 16S LiFePO4 packs are covered; and the mass limit in R12 is 2.0 kg instead of 1.5 kg, because the enclosure is also the heat sink. No requirement has been verified by test.
The **reference case** used throughout is a 250 W geared hub motor on a 48 V (46.8 V nominal) SwapCell pack at 40 °C ambient. The **heavy case** is 350 W continuous on a 25.6 V (8S) LiFePO4 pack at 40 °C ambient.
On paper, ten requirements are met and none is not met. R2, R9 and R10 are **at risk**; R11 cannot be verified at TRL 3. R12 is met with a margin of only 0.06 kg.
*Table 1. Requirements.*
| ID | Requirement | Target | Verification (TRL 3 or later) | Status at TRL 3 (MTC-CAL-001) |
| --- | --- | --- | --- | --- |
| R1 | Supply range | Operate from 20 to 60 V DC (8S LiFePO4 to 13S lithium-ion and 16S LiFePO4, including SwapCell at 54.6 V full and CellGuard 16S at 58.4 V full); withstand 75 V transients from regeneration | Controller and contactor datasheets; bus voltage calculation | Met (design review): 75 V controller, 18 to 75 V auxiliary buck, bus peaks near 67.8 V with a 66 V controller overvoltage fault |
| R2 | Motor power | 250 W continuous in the reference case; 350 W continuous in the heavy case; 750 W for 10 s | Current and thermal calculation | **At risk:** met electrically (6.9 A, 17.7 A; 750 W peak 21.9 A on SwapCell, 40.9 A on 8S LiFePO4); heavy case limited by R9 |
| R3 | Hardwired emergency stop | Twin-channel normally closed e-stop wired in series with the contactor coil; motor power removed within 100 ms of actuation; works with the supervisor and controller both failed | Circuit review; contactor drop-out time from datasheet | Met on paper: 67 ms worst case, 30 ms modeled; unverified |
| R4 | No automatic restart | After an e-stop, power loss or fault, the drive stays off until the e-stop is released, the throttle is at zero and the operator cycles the enable key | Circuit and state-machine review | Met (design review); unverified |
| R5 | Brake interlock | Two brake switch inputs; drive torque removed within 200 ms of either switch opening; a spring-applied brake output released only while the safety loop is closed | Circuit review; supervisor timing budget | Met on paper: about 75 ms; unverified |
| R6 | Independent speed limit | Speed limit set in the controller and checked by the supervisor from a separate sensor; overspeed of more than 10 % for more than 0.5 s opens the contactor; defaults 25 km/h (pedal assist) and 1.5 m/s (walk-behind) | Firmware review; sensor resolution calculation | Met on paper: period timing, fivefold margin over magnet jitter, trip in 0.60 to 0.70 s; unverified |
| R7 | Fault reaction | Supervisor removes torque within 200 ms of: command timeout, throttle signal outside 0.5 to 4.5 V, loss of controller CAN heartbeat, over-temperature or BMS fault flag | Fault table review | Met on paper: about 170 ms worst (controller heartbeat), about 80 ms for a BMS fault; unverified |
| R8 | Precharge | Inrush at contactor closure under 5 A; bus ready within 1 s | Precharge calculation | Met: 0.55 A peak, 1.3 A at closure, ready in 0.6 s |
| R9 | Thermal | Enclosure surface 60 °C or less at 40 °C ambient in natural convection | Thermal calculation | Reference case met (50.2 °C); **heavy case at risk** (58.5 °C; 65 to 71 °C in sensitivity cases) |
| R10 | Ingress and vibration | Enclosure and mated connectors IP65; survive road and stair vibration without loosening | Datasheets and design review | **At risk:** the XT90 power socket is not sealed; a sealed power connector is to be evaluated before interface v0.1 is frozen (MTC-DDR-002); vibration not analyzed |
| R11 | One interface | One documented connector set (power in, motor, sensors, safety loop, command) keyed against mis-mating; fitted to a new host in 2 h or less with hand tools | Interface document; timed fit at TRL 4 | Not verifiable at TRL 3: interface v0.1 adopted and drawn (MTC-DWG-001) |
| R12 | Size and mass | Module within 250 x 170 x 70 mm; module mass 2.0 kg or less (1.5 kg before MTC-DDR-002) | Model and mass estimate | Met: 243 x 168 x 66 mm; about 1.94 kg, 0.06 kg margin |
| R13 | Open and repairable | Hardware under CERN-OHL-S-2.0; supervisor firmware MIT; controller firmware open source; fault log readable over USB without closed software | License review | Met (design review): separate programs on separate processors, CAN link only; formal license review open |
| R14 | Cost | MotionCore kit (module and devices, BOM items 2 to 14) $300 or less in parts; the reference motor is costed to each host | Priced BOM (`bom/bom.csv`) | Met on indicative prices: $265 (reference motor $70 extra) |
## Assumptions
- Motor efficiency about 80 % at rated load; controller losses from a component model (MTC-CAL-001 Table 1), which gives about 98 to 99 % controller efficiency; to be checked against datasheets once parts are chosen.
- Contactor release time 50 ms or less with a 24 V Zener coil suppressor; this is a selection criterion for the part.
- Enclosure conductance about 1.17 W/K from simplified natural convection and radiation correlations, clear anodized, shaded (MTC-CAL-001 section 4).
- The host provides mechanical brakes able to stop it with the motor unpowered. MotionCore removes drive power; it does not replace the host's brakes.
- The host carries out its own risk assessment. MotionCore targets are not a claimed ISO 13849 performance level.