Loading files
This file is pinned to the selected release. Download the original to open it in your design tool.
88e0f32bdThis file is pinned to the selected release. Download the original to open it in your design tool.
`timescale 100ns/1ns
`default_nettype none
`include "Uart8.v"
module test;
localparam CLOCK_FREQ = 12000000; // Alhambra board
localparam SIM_STEP_FREQ = 1 / 0.0000001 / 2; // this sim timescale 100ns
// for the simulation timeline:
// ratio SIM_STEP_FREQ MHz / CLOCK_FREQ MHz gives the output waveform in proper time
// (*but note all clocks and the timeline are approximate due to rounding)
localparam SIM_TIMESTEP_FACTOR = SIM_STEP_FREQ / CLOCK_FREQ;
reg clk;
reg en_1;
reg rx;
wire rxBusy_2;
wire rxDone_2;
wire rxErr_2;
reg [7:0] txByte_1;
wire [7:0] rxByte_2;
Uart8 #(.CLOCK_RATE(CLOCK_FREQ)) uart(
.clk(clk),
// rx interface
.rxEn(en_1),
.rx(rx),
.rxBusy(rxBusy_2),
.rxDone(rxDone_2),
.rxErr(rxErr_2),
.out(rxByte_2)
// tx interface (unused)
);
initial clk = 1'b0;
always #SIM_TIMESTEP_FACTOR clk = ~clk;
initial begin
$dumpfile(`DUMP_FILE_NAME);
$dumpvars(0, test);
// #65 == 1 rx clock period (approximately) at 9600 baud
#240
en_1 = 1'b1;
txByte_1 = 8'b11010110;
rx = 1'b0;
$display(" tx data: %8b", txByte_1);
#160
rx = 1'b1;
#360
rx = 1'b0;
#1075 // instead of #1042, this makes transmit clock sync with receive clock (a 3% difference)
rx = txByte_1[0];
$display("%7.2fms | rx first bit: %1b", $realtime/10000, rx);
#1075
rx = txByte_1[1];
$display("%7.2fms | rx next bit: %1b", $realtime/10000, rx);
#1075
rx = txByte_1[2];
$display("%7.2fms | rx next bit: %1b", $realtime/10000, rx);
#1075
rx = txByte_1[3];
$display("%7.2fms | rx next bit: %1b", $realtime/10000, rx);
#1075
rx = txByte_1[4];
$display("%7.2fms | rx next bit: %1b", $realtime/10000, rx);
#1075
rx = txByte_1[5];
$display("%7.2fms | rx next bit: %1b", $realtime/10000, rx);
#1075
rx = txByte_1[6];
$display("%7.2fms | rx next bit: %1b", $realtime/10000, rx);
#1075
rx = txByte_1[7];
$display("%7.2fms | rx last bit: %1b", $realtime/10000, rx);
#530
rx = 1'b1;
#630
rx = 1'b0;
$display("%7.4fms | end of stop bit | start of start bit: %1b", $realtime/10000, rx);
#610
rx = 1'b1;
$display("%7.4fms | end of start bit: %1b", $realtime/10000, rx);
#920
rx = txByte_1[0];
$display("%7.2fms | rx first bit: %1b", $realtime/10000, rx);
#1075
rx = txByte_1[1];
$display("%7.2fms | rx next bit: %1b", $realtime/10000, rx);
#1075
rx = txByte_1[2];
#1000
$finish();
end
endmodule