stmbl

DISCLAIMER
===
THE AUTHORS OF THIS SOFTWARE ACCEPT ABSOLUTELY NO LIABILITY FOR
ANY HARM OR LOSS RESULTING FROM ITS USE.  IT IS _EXTREMELY_ UNWISE
TO RELY ON SOFTWARE ALONE FOR SAFETY.  Any machinery capable of
harming persons must have provisions for completely removing power
from all motors, etc, before persons enter any danger area.  All
machinery must be designed to comply with local and national safety
codes, and the authors of this software can not, and do not, take
any responsibility for such compliance.

This software is released under the GPLv3.

stmbl
=====
**PCBs are now available, let me know if you are interested.**

**IRC: #stmbl on hackint.eu**

stmbl is an open source servo drive designed for Retrofitting CNC machines and Robots. It supports Industrial AC and DC servos with up to 320V and 1kW.

Documentation about the PCB and pinout of the feedback connector:

https://github.com/rene-dev/stmbl/wiki/Pinouts

https://github.com/rene-dev/stmbl/wiki/PCB

##### Hardware version 3.2
![top](http://rene-dev.github.io/iramx32top.jpg)
![bot](http://rene-dev.github.io/iramx32bot.jpg)

##### Driving a Bosch Turboscara
https://www.youtube.com/watch?v=Ue98HE76paI
##### Drivetest
https://www.youtube.com/watch?v=sMeV4SCu4TA
##### Drivetest with asymmetrical load
https://www.youtube.com/watch?v=seEV_i7o1NI

####Supported Motors
* Synchronous AC Servos
* DC Servos
* 2 Phase HF spindle motors
* IRAMXv2 Hardware testet up to 320V

####Supported Feedback systems
* Resolvers
* Incremental encoders
* sin/cos encoder interpolation
* Mitsubishi absolute encoders

####TODO
* AC Async
* saving parameters to flash

####Directories
* hw/eagle/ Eagle board files and schematics
* hw/spice/ Spice simulation for resolver interface
* src/ STM32F4 code, command, feedback and control loop
* stm32f103/ STM32F1 code, running on the HV side, generating PWM
* term/ Terminal with scope and local history. Supports UHU servo and stmbl.


####Building the firmware
##### Requirements
* gcc-arm-none-eabi-gcc https://launchpad.net/gcc-arm-embedded/+download
* stlink https://github.com/texane/stlink

##### Flashing
Add gcc and stlink to your $PATH

    make
    make burn

####Building Servoterm
##### Requirements
* cmake >= 2.8
* gcc >= 4.8 or clang
* wxwidgets >= 3.0
* libserialport http://sigrok.org/wiki/Libserialport

##### Compiling

    cd term/
    mkdir build/
    cmake ../
    make

####Using Servoterm
##### Testing HAL
HAL can be tested without any hardware connected to the STM32F4discovery.
* Flash STM32F4discovery(STlink and USB OTG must be connected)
* Launch Servoterm, Click refresh, and connecto to STM32 Virtual ComPort

entering 'list' prints a list of hal pins.
The current default config is for a 4 pole AC permanent magnet motor with resolver feedback, using an encoder for command. 

> net0.fb <= res0.pos = 0.000000

net0.fb is driven by res0.pos, and its current value is 0. Pins can be connected to other pins, or fixed values.

This example connects the sine wave generatror to wave view 0.
Offset and gain can be controlled with the sliders below Channel 1(black).
```
term0.wave0 = sim0.sin
sim0.amp = 10
sim0.freq = 5
```
To disconnect a pin, connect it to itself
```
term0.wave0 = term0.wave0
```