Ram Tester for vintage CBM Computer RAM Chips
Loading README and project media…
Fast, open-source DIY tester for vintage DRAM/SRAM — auto-detects the chip type, runs every test, gives a clear good/bad in seconds.
[GPL v3] [Firmware 5.1.2] · C64 · Amiga · Atari · ST · Apple II · Spectrum
A fast, open-source DIY RAM tester for vintage RAM chips used in C64, Amiga, Atari, and other retro computers. Built around a 16MHz ATmega328P on a custom PCB, it tests memory thoroughly in seconds and supports a wide range of chip types with optional OLED feedback.
As featured on:
| Feature | Benefit |
|---|---|
| 20-pin ZIP socket | Direct test of 20-pin ZIP DRAMs without an adapter |
| Optional OLED display or LED blink codes | Full text feedback or minimal hardware setup |
| Self-test mode | Verify the hardware for defects like short circuits or broken solder joints |
| Capacity | DIP | 20-pin ZIP | Static Column | Nibble Mode | Retention Time | Test Time |
|---|---|---|---|---|---|---|
| 4 K × 1 | 4027 1) | – | – | – | 2 ms | 0.2 s |
| 16 K × 1 | 4816 | – | – | – | 2 ms | 0.7 s |
| 16 K × 1 | 4116 1) | – | – | – | 2 ms | 0.5 s |
| 16 K × 4 | 4416 | – | – | – | 4 ms | 1.7 s |
| 32 K × 1 | 3732 2) | – | – | – | 2/4 ms | 1.8 s |
| 32 K × 1 | 4532 2) | – | – | – | 2/4 ms | 1.8 s |
| 64 K × 1 | 4164 | – | – | – | 2/4 ms | 1.8 s |
| 64 K × 4 | 4464 | – | – | – | 4 ms | 5.2 s |
| 256 K × 1 | 41256 | – | – | 41257 | 4 ms | 7.5 s |
| 256 K × 4 | 44256 | both | 44258 | – | 8 ms | 3.5 s |
| 1 M × 1 | 411000 | ✗3) | – | – | 8 ms | 19.4 s |
| 1 M × 4 | 514400 | both | 514402 | – | 16 ms | 12.0 s |
1) Requires the 4116 adapter board. 2) Half-good 4164 chips sold as 32K × 1 (OKI MSM3732 / TI TMS4532). Enabled by default since firmware 4.2.3. See 32K documentation for details. 3) The ZIP pinout is different than the 20-pin DIP — for the ZIP version you need an adapter!
Static Column means the RAM allows column changes while CAS is held low — faster than standard page mode. Nibble Mode delivers four consecutive bits from one column address.
| Capacity | DIP | Test Time |
|---|---|---|
| 1 K × 4 | 2114 1) | 0.4 s |
1) WARNING: 2114 SRAM needs to be inserted 180° rotated, with Pin 10 of the SRAM on the ZIF Pin 1 marking.
There is a short YouTube video demonstrating the tester in action.

Here is the analytics of this algorithm vs. March-B
| Aspect | This Tester | MARCH-B |
|---|---|---|
| Pattern Coverage | ✅ Checkerboard | ✅ |
| 0→1 / 1→0 Transition | ✅ Via pattern sequence | ✅ Via R0W1, R1W0 |
| Address Sequence | ✅ Asc + Descending | ✅ Asc + Descending |
| Coupling Detection | ✅ Via retention delay | ✅ Systematic |
| Real Retention | ✅ 2–16 ms per chip spec | ❌ Not covered 1) |
| GND Short Detection | ✅ Before test | ⚠️ Implicit only 1) |
| Address Line Faults | ✅ Bit-independence check | ⚠️ Implicit only 1) |
| CBR Refresh | ✅ CAS-before-RAS test2) | ❌ Not covered 1) |
1)unless implemented outside of MARCH-B 2)For RAM that have a Refresh Counter (41256 and newer)
March-B is thorough for coupling and decoder faults but operates in the microsecond range — it cannot catch chips with weak retention that meet spec on paper but fail under real-world refresh timing. This tester trades systematic address ordering for real-time retention stress, which is where most age-related failures actually occur.
Vintage DRAM chips were designed for TTL signal levels. The ATmega328P drives CMOS levels at 5 V — logic high is close to VCC, which is above what the original systems delivered. This means marginal chips that fail at true TTL thresholds may still pass on this tester (and most other microcontroller-based testers). Some designs use 3.3 V controllers with 5 V-tolerant I/O to get closer to TTL levels, but the ATmega328P does not support this operating mode. In practice, virtually no consumer DRAM tester on the market operates at true TTL levels — this is a fundamental limitation of the approach, not specific to this project. For definitive TTL-level testing, dedicated vintage test equipment (e.g. Advantest, Agilent) operating at calibrated thresholds would be needed.
Buy ready-made: Amibay · Lectronz · eBay · Tindie
Build it yourself (DIY): Available as a beginner-friendly through-hole (THT) version or a compact SMD version. Order PCBs at PCBWay (TH) or use the provided Gerber files from the Schematic folder.
You're welcome to build, modify and even sell your own Ram-Testers — that's the point of open hardware. In return, the license asks you to keep it open:
In short: build it, improve it, sell it — just keep it open and point people back here. If unsure, open a Discussion and ask.
Pull requests, issues and forks are welcome. Questions: GitHub Discussions or contact tops4u on AmiBay.
Open-source hardware (CERN-OHL-S v2) and firmware (GPL v3) – use at your own risk.