optocamzero

# Optocam Zero V1.0 Bill of Materials
Doruk Kumkumoğlu 2026

<br>

## Electronics

| Item | Qty |
|------|-----|
| [Raspberry Pi Zero 2 W (without header)](https://thepihut.com/products/raspberry-pi-zero-2) | x1 |
| [Raspberry Pi Camera Module 3](https://thepihut.com/products/raspberry-pi-camera-module-3) | x1 |
| Micro SD Card A2 Class — Raspberry Pi or other high quality brands, minimum 16GB | x1 |
| [Waveshare Li-ion Battery HAT for Raspberry Pi](https://www.waveshare.com/li-ion-battery-hat.htm) | x1 |
| [Waveshare 1.3" IPS 240x240 LCD Display HAT for Raspberry Pi](https://www.waveshare.com/1.3inch-lcd-hat.htm) | x1 |
| [Camera Adapter Cable – Raspberry Pi Zero compatible (200mm)](https://thepihut.com/products/camera-adapter-cable-for-raspberry-pi-5) | x1 |
| 14500 Type 3.7V 900 mAh Li-ion Battery | x1 |
| Micro JST 1.25 Pitch 2 Pin Male and Female Connector Set (with 24 AWG cable) — or 24 AWG cable (≥50cm length) | x1 |
| [2×20 Double Row Male GPIO Header](https://thepihut.com/products/break-away-0-1-2x20-pin-strip-dual-male-header) | x1 |
| 0.3mm Ø Enameled Copper Wire (≥30cm length) — or any thin signal cable | x1 |

Note: If you can find non-standard 8-9mm lenght pin headers, use those instead of the standard 2x20 double row header specified in the list.

<br>

## Fasteners

| Item | Qty |
|------|-----|
| M3×16mm Stainless Steel Hex-Drive Flat Head Screw | x4 |
| M2×6mm Screw (comes with the Waveshare Display HAT) | x2 | 
| [M3×4mm×4mm Brass Heat Set Insert](https://www.adafruit.com/product/4255) | x4 |
| 12×3×1mm Neodymium Magnet | x8 |

<br>

## Optional Fasteners

| Item | Qty |
|------|-----|
| M3×6mm Stainless Steel Hex-Drive Flat Head Screw (for lanyard accessory) | x2 |
| M3 Stainless Steel Nut (for lanyard accessory) | x2 |

<br>

## 3D Printed Parts and Materials

| Item | Material | Qty |
|------|----------|-----|
| Enclosure | PETG | x1 |
| Back Panel | PETG | x1 |
| Camera Cover | PETG | x1 |
| Camera Circle | PETG | x1 |
| Front Spacer | PETG | x1 |
| Front Panel | PETG | x1 |
| Battery Door | PETG | x1 |
| Battery Level Visor | PETG | x1 |
| On/Off Button | PETG | x1 |
| Joystick Button | PETG | x1 |
| Washer 1mm | PETG | x4 |
| Washer 4mm | PETG | x4 |

<br>

## Optional 3D Printed Parts

| Item | Material | Qty |
|------|----------|-----|
| Lanyard Lock Parts | PETG | x1 |
| Camera Sleeve | TPU | x1 |

<br>

## Optional – Cords & Straps

| Item | Qty |
|------|-----|
| Paracord – 1mm Ø, ≥30cm length | x1 |
| Paracord – 4mm Ø, ≥1m length | x1 |

<br>

## Tools

- 3D Printer
- Soldering Iron
- M3 Heat Set Insert Tip For Soldering Iron
- Solder Pump
- Solder
- Flux
- Kapton Tape
- 2mm (M3) Hex Driver
- Utility Knife
- Pliers
- Side Cutter
- Tweezers