Loading files
This file is pinned to the selected release. Download the original to open it in your design tool.
# Assembly Guide
## Overview
This guide will walk you through assembling the Nest Audio drop-in PCB.
**Skill Level**: Intermediate
**Time Required**: 2-3 hours
**Tools Required**: See Tools section below
## Prerequisites
Before you begin:
1. PCB is fabricated and tested
2. All components from BOM are received
3. Disassembled Nest Audio enclosure ready
4. Workspace with good lighting and ESD protection
## Tools Required
### Essential
- [ ] Temperature-controlled soldering station (350°C max)
- [ ] Hot air rework station
- [ ] Fine tip tweezers (ESD-safe)
- [ ] Magnifying lamp or microscope
- [ ] Flux (no-clean type)
- [ ] Solder wire (63/37 or lead-free, 0.5mm)
- [ ] Solder wick/braid
- [ ] Isopropyl alcohol (99%)
- [ ] Anti-static mat and wrist strap
### Optional but Helpful
- [ ] PCB holder/vice
- [ ] Fine tip solder sucker
- [ ] Thermal camera (for hot spots)
- [ ] Multimeter with continuity test
- [ ] Oscilloscope (for debugging)
## Component Installation Order
Install components in this order (lowest profile to highest):
### Step 1: Passive Components (SMD)
**Priority**: High
**Difficulty**: Easy
1. **Resistors and Capacitors (0603/0805)**
- Apply flux to pads
- Place component with tweezers
- Tack one side with soldering iron
- Solder other side
- Remove excess solder with wick if needed
2. **Ferrite Beads**
- Same procedure as resistors
- Note polarity marking (if applicable)
3. **Crystals**
- Handle carefully (fragile)
- Ensure proper orientation
- Check ground connections
### Step 2: Small ICs and Regulators
**Priority**: High
**Difficulty**: Medium
1. **LDO Regulators (SOT-23)**
- Apply flux to pads
- Align component (check pin 1 marking)
- Tack one corner pin
- Adjust alignment if needed
- Solder remaining pins
2. **MOSFETs (SOT-23)**
- Same as LDOs
- Verify orientation with datasheet
### Step 3: Power Components
**Priority**: High
**Difficulty**: Medium
1. **Buck Converter (TPS54202)**
- Apply paste flux to all pads
- Position IC with tweezers
- Use hot air at 300°C
- Heat until solder flows (30-60 seconds)
- Check alignment and solder joints
2. **Inductor (4.7uH)**
- Hand solder with iron
- Ensure good thermal connection
### Step 4: Microcontrollers (QFN Packages)
**Priority**: Critical
**Difficulty**: Hard
⚠️ **WARNING**: These are the most difficult components. Take your time.
1. **ESP32-S3R8 (QFN-56)**
- Apply solder paste to center pad and perimeter
- Position IC carefully (check pin 1 marking)
- Use hot air at 280-300°C
- Heat evenly around all sides
- Verify no bridged pins with microscope
- Check center pad connection (critical for heat dissipation)
2. **XMOS XU316 (QFN-60)**
- Same procedure as ESP32
- Extra care with 60 pins
- Check all corners for proper seating
### Step 5: Audio Amplifier
**Priority**: High
**Difficulty**: Medium
1. **MAX98357 (TQFN-16)**
- Hot air soldering recommended
- Check exposed pad connection (thermal and electrical)
- Verify no solder bridges on fine pitch pins
### Step 6: Connectors
**Priority**: Medium
**Difficulty**: Easy
1. **USB-C Connector**
- Apply flux
- Position and tack one ground pin
- Check alignment
- Solder all pins
- Reinforce mechanical mounting tabs
2. **Barrel Jack**
- Through-hole mounting
- Solder from top and bottom for strength
3. **Pin Headers**
- Insert from top
- Solder from bottom
- Check for straightness
### Step 7: LEDs and Microphones
**Priority**: Medium
**Difficulty**: Medium
1. **SK6812 RGB LEDs (6x)**
- ⚠️ **HEAT SENSITIVE** - Use low temperature (280°C max)
- Check polarity (DI/DO pins)
- Install in correct order for data chain
- Test after each LED if possible
2. **MEMS Microphones (2x)**
- Use minimal heat
- Check orientation (sound port direction)
- Ensure clean solder joints (affects audio quality)
### Step 8: Final Components
**Priority**: Low
**Difficulty**: Easy
1. **Push Buttons (2x)**
- Through-hole
- Check alignment with enclosure
2. **Programming Header (Optional)**
- Can be omitted if using USB-C for programming
## Post-Assembly Checks
### Visual Inspection
- [ ] No solder bridges on IC pins
- [ ] All components properly oriented
- [ ] No cold solder joints
- [ ] No damaged components
- [ ] Clean flux residue with isopropyl alcohol
### Electrical Testing
Use multimeter to check:
- [ ] No shorts between power rails
- [ ] Correct voltage on 3.3V rail
- [ ] Correct voltage on 5V rail
- [ ] Continuity on critical traces
- [ ] Ground connections
### Power-On Test
Before installing in enclosure:
1. Connect 14V power supply
2. Check current draw (< 100mA idle)
3. Check 3.3V and 5V rail voltages
4. Look for hot components
5. No magic smoke = good!
## Common Issues
### ESP32 Not Responding
- Check center pad soldering (ground/heat sink)
- Verify 3.3V regulator output
- Check USB-C data lines
### No Audio Output
- Verify amplifier power (5V)
- Check speaker connections
- Verify I2S signals with scope
### LEDs Not Working
- Check 5V supply to LED chain
- Verify data line continuity
- Check LED polarity
### Microphone Not Working
- Verify 3.3V supply
- Check I2S connections to XMOS
- Verify microphone orientation
## Cleaning
After assembly and testing:
1. Clean all flux residue with 99% isopropyl alcohol
2. Use soft brush for stubborn areas
3. Let dry completely before powering
4. Optional: Apply conformal coating for protection
## Next Steps
After successful assembly:
1. Proceed to [Flashing Guide](flashing-guide.md)
2. Test basic functionality
3. Install in Nest Audio enclosure
4. Configure with Home Assistant
## Troubleshooting Resources
- [ESPHome Voice Assistant Documentation](https://esphome.io/components/voice_assistant.html)
- [Home Assistant Voice Setup](https://www.home-assistant.io/voice/)
- GitHub Issues: Report problems here
- Community: Home Assistant forums
## Safety Notes
⚠️ **Important Safety Information:**
- Always wear safety glasses when soldering
- Work in well-ventilated area
- Use ESD protection
- Hot components can cause burns
- Unplug power before making modifications
- Double-check polarity before applying power
## Support
Having trouble?
- Check [Troubleshooting Guide](troubleshooting.md)
- Open an issue on GitHub
- Ask in the Home Assistant community
**Good luck with your build!**
7e387f535This file is pinned to the selected release. Download the original to open it in your design tool.