Loading files
This file is pinned to the selected release. Download the original to open it in your design tool.
1908e515dThis file is pinned to the selected release. Download the original to open it in your design tool.
# Moraydular Virta #
A 100x200mm hybrid power supply design for Eurorack modular synthesizers.
Virta uses external SMPS DC wallwart as input, splits and regulates down to +-15V and +5V via standard 1x2 or 1x1 inch DC-DC blocks, then regulates +-15V down to +-12V using low dropout (LDO) linear regulators. Pi filters are included on the PCB between DC-DC stages for attenuating high frequency switching noise before final linear regulation stage. There is a provision for dummy load resistors for those DC-DC converters requiring a minimum load for stability.
This should theoretically provide for a high quality power output without mains power inside the enclosure, at the expense of high parts cost (compared to a standard LM317/LM337 transformer-based power supply or plain SMPS) and less than ideal efficiency.
## Ordering and Building Notes ##
For now this is "at your own risk" type advanced project. I haven't exactly specified the part numbers to use because it hasn't been confirmed whether they're ideal and working for the limits I have specified. Furthermore, both DC-DC converters and LDOs may be a bit picky in auxiliary components.
Notes:
- There is one error in v0.6 PCB: the ON/OFF pin of LM2991 should be tied to ground with a resistor leg or similar. MAY work without that modification.
- For current V0.6 PCBs the 1"x1" footprint DC-DC holes are noticeably smaller than for the 1"x2" pinout, so all 1"x1" DC-DCs won't fit!
- C31 should NOT be populated, it's there by mistake and will cause LM2991 to oscillate.
## Bill of Materials ##
- 6x 100uF low ESR electrolytic (C1-C3, C16-C18)
- 11x 0.1uF MLCC ceramic (C4-C6, C13-C15, C22-C24, C28-C29)
- 9x 0.1uF 0805 SMD ceramic (C7-C12, C19-C21, optional, should improve switching noise filtering, may cause problems with some DC-DCs)
- 3x 47uF low ESR electrolytic (C25-C27)
- 3x 10uF (low ESR) electrolytic (C30, C32, C33)
- 4x any of 1N4001 to 1N4007 (D1-D4)
- 1x PCB mount 5x20mm fuse holder (F1 + a 5x20mm fuse according to your power use)
- 3x 0.1" 2-pin headers for dummy load jumpers (J1-J3, may be left out if dummy load not used)
- 4x ~10uH 2A+ radial / vertical inductor (L1-L4)
- 3x standard 3mm led (LED1-LED3, pick a color and adjust resistors accordingly)
- 2x isolated 15V DC-DC converter (ISOL 15v, specifications according to required power)
- 1x isolated 5V DC-DC converter (ISOL 5V, specifications according to required power)
- 14x PCB mount 6,3mm Faston / Abiko / quick disconnect terminals
- 1x LM2991T (U1)
- 1x LM1086CT-ADJ (U2, may use LM1084 or LM1085 but has to be -ADJ version)
- 2x "fin" style TO220 heatsink (height according to required power)
- 2x 1K "3296Y" style vertical multiturn trimmer (TR1, TR2)
- 1x 220R 1/4W resistor (R6)
- 4x 1K 1/4W resistor (R5, R7, R9, R10)
- 2x 8.2K 1/4W resistor (R4, R8)
- 2x 0.5R 5W power resistor (R1, R2)
- 1x 0.22R 5W power resistor (R3)
- 2x 56R 5W power resistors (RL1, RL2, optional, only if dummy load needed)
- 1x 22R 5W power resistor (RL3, optional, only if dummy load needed)
- 1x SMPS wall wart according to required power and chosen DC-DC converters