Jeden board
A development board based on ATMega328P microcontroller, which has functionality of a Arduino Uno and a USB-C port.

[photo of the board after manufacturing, the LED 1 was not soldiered in the factory but lack of it does not affect the functionality]
Features:
- USB-C port for power and uploading software (requires Arduino bootloader).
- ISP pins for programming and bootloader upload, USB-UART via FT232RL, other means of communication ATMEGA328P supports can be used if wired correctly.
- 5V operation voltage.
- Microcontroller auto-reset after programming.
- Polyfuse, ferrite bead, capacitors between VCC and GND lines, and diodes for protection and voltage stabilization.
- Can be manufactured.
- Has same (gold)pins available as an Arduino Uno, but is not compatible with Uno shape-wise.
- 16.0000 MHz clock.
- Two LEDs - one for VCC status and the other connected to D13.
- Similar size to a Arduino Uno.
Burning the bootloader
I successfully burned the Arduino bootloader onto the board by using a genuine Arduino Uno as ISP programmer.
In Arduino IDE I uploaded the ISP programmer software into the Uno, then wired it to my board's ISP pins, then chose Arduino Uno as the board's model and clicked "Burn the bootloader".
I recommend turning on visibility of programmer's output in the Arduino IDE to see if the process was successfull. If it fails, you may have to try again several times.
If using bootloader of a Arduino Uno fails, try using MiniCore and choose ATMega328P at 16 MHz.
After successfull bootloader burning, the Jeden board should be visible after connecting to your computer via USB. It will be then possible to write and upload software to it via USB, just like if you were using a Arduino Uno. The board will not provide any model name tho, so you will see a unnamed/empty device name on a USB connection (in case of Windows under a COM port).
Notes, precautions, and errors I know the board has:
- This board is very amateur and is likely to be unrealiable, please do not use it in any mission-critical systems. It's my first design of a device like this, and one of first PCBs I ever designed. It might have hidden flaws that I haven't noticed. I have not tested (yet) how it behaves in non-room conditions, working for very long time nor under heavy load.
- AREF is hardwired to the GND line, so analog pins might not have too good accuracy.
- There are several connections on the PCB where the wires change direction in 90 degrees. I learned that such bends shouldn't be done after I sent the board for manufacturing. Since the board works tho, I decided to not make modifications to it.
- The 3.3V OUT pin on the board is connected to 3.3V OUT pin of the FT232RL. According to what I read, that was supposed to give me a 3.3V VCC line. The pin does not work tho on the board I recieved, and I recommend not using it at all, just in case.
- The USB-C port will likely be connected to the PCB quite weakly, so please be careful and hold it when unplugging USB-C cables from Jeden.
- The resistor between ~RESET and VCC lines in the design is 5100 Ohm, but theoretically should be 10k Ohm. Resetting the board works regardless of this tho.
Feedback, including tips and critique; is appreciated. It was a very interesting project to do, and I'm happy to learn more about PCB design.
Translations:
Notes on the schematic are written in Polish, so here are translations of them to English:
- Dławik ferrytowy - means ferrite choke, but the component on the PCB is a ferrite bead. I first translated it wrong from English to Polish when reading papers on how to create the VCC line.
- "Kondensatory podłączyć blisko ATMEGA" - "Connect (place) the capacitors near the ATMEGA".
- Ceramiczny niespolaryzowany - ceramic non-polarized (capacitor).
- Elektrolityczny spolaryzowany - polarized electrolytic (capacitor).
- Jeden - One (1). I named the board this way as reference to Arduino Uno.