JDY-08 Bluetooth transparent transmission module

Feature

• Tested on 3V3
• Module enter into data transmission mode when it paired.
• Pull P00 to low to wake up the module from sleep mode, then module can accept data tranmission.
• serial data send need "/r/n"
• Power supply must use 3.3 or 3V for final products
• master module can only allow one slave module connect
• in room distance is 15-30 meters, max to 60 meters.
• Tranmission data speed is 1KB/s
• Do not support 2.0 or 3.0 bluetooth version.

Operating mode state current

• Slave Transparent Mode Connected / Not Connected / Standby 0.8mA / 300uA / 1uA
• Slave Broadcast mode (IBeacon, sensor) Connection / Not connected / Standby 0.5mA / 300uA / 1uA
• Host Transmitted Mode Connect / Unconnected / Standby 20mA / 9mA / 1uA
• Host observer mode (Sensor) connected / not connected / standby 25mA

Dimension, Pin definition

Pin definition

1. VCC Power Supply Power supply 3V or 3.3V
2. P22
3. P21
4. P20
5. P17
6. P16 connection status pin Bluetooth connection is low, usually high (master-slave effective)
7. P11 PWM2 The PWM2 output pin can be controlled by the APP
8. P12 IO1 Output The IO1 pin can be controlled by the APP level
9. P13 IO2 Output The IO2 pin can be controlled by the APP pin
10. P15 IO3 Output The IO3 pin can be controlled by the APP pin
11. SCK
12. SDA
13. P14 IO4 Output The IO4 pin can be controlled by the APP pin
14. P10 PWM1 The PWM1 output pin can be controlled by the APP
15. P07 PWM3 The PWM3 output pin can be controlled by the APP
16. P06 PWM4 The PWM4 output pin can be controlled by the APP
17. P05 RTC Alarm IO IO output low when the RTC timing time expires
18. P04 RTC Alarm IO IO output low when the RTC timing time expires
19. P03 TXD serial output, the level is TTL level
20. P02 RXD serial port, the level is TTL level
21. P01 IO disconnected Bluetooth connection status is down to delay the connection, usually high
22. P00 PWRC module sleep wake-up pin, the module internal pull-up resistor, low-level wake-up, usually high
23. RST Resets the hardware reset pin
24. GND Power ground

Boards:

• Resources a simple breakout board design for development. By Danny Staple (Orionrobots)

Resources for development in KiCAD...

AT Commands

1. AT + RST reset M / S -
2. AT + BOUD serial port baud rate setting M / S - 115200
3. AT + HOSTEN Master / Slave Setup M / S - Slave
4. AT + HOST Read Host Status M -
5. AT + DISC Disconnect M -
6. AT + ADVEN Open Broadcast S - On
7. AT + ADVIN Broadcast interval S - 100ms
8. AT + NEIN Connection Interval S - 10ms
9. AT + POWR Transmit power S - 0db
10. AT + NAME broadcast name S - EB - 08
11. AT + MAC Read MAC Address M / S -
12. AT + STRUUID Set iBeacon UUID (string type UUID) S iBeacon UUID
13. AT + HEXUUID setting iBeacon UUID (hexadecimal type UUID) S iBeacon micro letter UUID
14. AT + MAJOR Sets iBeacon Major (string type Major)
15. AT + MINOR Set iBeacon Minor (string type Minor) S iBeacon 7
16. AT + VER Read version number M / S - JDY-08-2.1
17. AT + VID Manufacturer’s identification number (not for factory identification) S iBeacon Sensor 8899
18. AT + TEMP Temperature Value Sets the Sipacon sensor
19. AT + HUMID Temperature setting S iBeacon sensor 0
20. AT + ISCEN Set whether to open the password connection S - Off
21. AT + PASS connection password S - 123456
22. AT + SVRUUID Change service UUID M / S - FFE0
23. AT + CHRUUID Change feature UUID M / S - FFE1
24. AT + SCAN Host Scan Slave M Host transparently transmitted
25. AT + RSLV Reads the MAC-to-MAC transparent transmission from the master
26. AT + CONNET CONNECTIONS SCAN TO MAC MOST TRANSMISSION FROM SLAVE
27. AT + BAND Bind slave MAC M -
28. AT + GETDCD Number of slaves scanned by the master M -
29. AT + GETSTAT Find the working status of the module M / S -
30. AT + PWMFRE Set the PWM frequency M / S - 500HZ
31. AT + PWMOPEN Turns PWM M / S - off
32. AT + PWM1PUS Sets the pulse width of PWM1 M / S - 50%
33. AT + PWM2PUS Sets the PWM2 pulse width M / S - 50%
34. AT + PWM3PUS Sets the pulse width of PWM3 M / S - 50%
35. AT + PWM4PUS Sets the pulse width of PWM4 M / S - 50%
36. AT + RTCDATE Setting the RTC time M / S -
37. AT + RTCOPEN Turn on the RTC function M / S - Off
38. AT + WXSVR Micro-H5 communicates with the server settings S-micro-H5

AT instructions

---

Commands	AT	return
Soft reset	AT + RST	Returns: OK
Setting the baud rate Note: The module default baud rate is 115200	Instruction: AT + BOUD0 means the baud rate is 115200, 1 means the baud rate is 57600, 2 means the baud rate is 38400, 3 means the baud rate is 19200, 4 means the baud rate is 9600	Returns: OK
Set the module operating mode	AT + HOSTEN0 means to set the slave transparent transmission (APP) mode. 1 means to set the host transparent mode, 2 means to set the host (indoor positioning, sensor) observer mode, 3 means to set the host (indoor positioning, sensor) observer mode, 4 means to set the slave (WeChat transmission) mode	Returns: OK
Disconnect	AT + DISC Disconnect	Returns: OK
Open the radio	Command: AT + ADVEN0 Stop broadcasting, AT + ADVEN1 means to turn on the broadcast, do not turn on the radio after power on	Returns: OK
Broadcast interval	Instruction: AT + ADVIN0 means to set the broadcast interval to: 100ms, 1 means to set the broadcast interval to: 500ms, Instruction: AT + ADVIN2 means to set the broadcast interval to: 750ms, Instruction: AT + ADVIN3 means to set the broadcast interval to: 1000ms, Instruction: AT + ADVIN4 means to set the broadcast interval: 2000ms, Instruction: AT + ADVIN5 means to set the broadcast interval to: 4000ms, Instruction: AT + ADVIN6 means to set the broadcast interval to: 8000ms	Returns: OK
Connection Interval	Instruction: AT + NEIN0 connection is 10ms, Command: AT + NEIN1 connection is 100ms, Command: AT + NEIN2 connection is 500ms	Returns: OK
Transmission power	Instruction: AT + POWR0 that set the transmit power to 4db CC2541 module this is 0db, Command: AT + POWR1 means to set the transmit power to 0db, Command: AT + POWR2 that set the transmit power -6db, Command: AT + POWR3 means to set the transmit power to -23db	Returns: OK
Transmission power	Instruction: The AT + POWR instruction is followed by a read without parameters	Returns: POWR0db indicates that the module transmit power is: 0db
Set the broadcast name	Instruction: AT + NAMEEB-08 means to set the broadcast name: EB-08	Returns: OK
Set the broadcast name	Instruction: The AT + NAME instruction is followed by a read without parameters	Returns: JDY-08 Indicates that the module broadcast is named JDY-08

Devices End Instructions

---

• Phone side command

Name	Instructions
UUID list	* Service UUID: 0XFFE0 (service UUID default 0xffe0 user can change) FEATURES UUID: 0XFFE1 (for transparent transmission of the default 0xffe1UUID user can change) Feature UUID: 0XFFE2 (for module function configuration)

• WeChat UUID list, not listed here
• APP instructions for use

Name	Feature UUID	Description	Commands	Return
1) APP transparent transmission	UUID: 0XFFE1	FFE1 for the APP transparent transmission characteristics UUID (applied to the IOS or Android phone through the APP)
2) IBeacon UUID settings and read	UUID: 0XFFE2	Set the UUID instruction format: E1 + 11 + 16 hexadecimal UUID	Instruction: E111FDA50693A4E24FB1AFCFC6EB07647825
2) IBeacon UUID settings and read	UUID: 0XFFE2	Read the UUID instruction format: E1 +12	Instruction: E112	Back to: 12FDA50693A4E24FB1AFCFC6EB07647825 12 for the command header, FDA50693A4E24FB1AFCFC6EB07647820 for the UUID
3) IBeacon Major settings and read	UUID: 0XFFE2	Set Major Instruction Format: E2 +21 + 2 Hexadecimal	Instruction: E221000A Description Major is hexadecimal 000A
3) IBeacon Major settings and read	UUID: 0XFFE2	Read the Major	instruction: E222	Returns: 22000A Description 22 for the command header, 000A for the hexadecimal Major
4) IBeacon Mimor set and read	UUID: 0XFFE2	Set the broadcast interval	instruction format: E3 +41 + 2 hexadecimal Minor Command: E3320007 means to set Mmior to hex 0X0007 Command: E332 means reading the Minor hexadecimal value	Returns: 320007 Description 32 is the command header, 0007 is the hexadecimal Minor
4) Broadcast interval setting and reading	UUID: 0XFFE2	Set the broadcast interval	instruction format: E4 +41 + 1 hexadecimal data Command: E44100 means to set the broadcast interval to 100ms Command: E442 Indicates read broadcast interval	Returns: 4200 Description 42 is the command header, 00 means the broadcast interval is: 100ms The APP sends the command broadcast interval E44200 100ms E44201 500ms E44202 750ms E44203 1000ms E44204 2000ms E44205 4000ms E44206 8000ms
5) Connect password settings and read	UUID: 0XFFE2	Set the connection password	Instruction format: E5 + 51 + 6-bit current password + 6-bit new password Instructions: E551313233343536313132323333 said after the set of passwords: 11223344 The new password can be set only when the current password is the same as the module password, and the password before the password is updated will be invalid
6) Broadcast name setting and reading

Working Mode Wiring

Working Mode

Working in relay control mode

use app "IO_ctrl", when button on bluetooh board pressed, app will receive relevant UUID data, when switch in app is pressed, UUID will send to EB08

iBeacon mode

1. Step 1: Configure the module as an iBeacon mode command
2. Send via serial port: AT + HOSTEN3 Returns: OK
3. Step 2: Let the module restart
4. Send via serial port: AT + RST means reset
5. Step 3: Change the UBID of iBeacon to (FDA50693A4E24FB1AFCFC6EB07647825)
6. Send via serial port: AT + STRUUIDFDA50693A4E24FB1AFCFC6EB07647825 Back: OK
7. Step 4: Change the Major value of iBeacon to (10)
8. Send via serial port: AT + MAJOR000A returns OK
9. Step 5: Change the minor value of iBeacon to (7)
10. Send via serial port: AT + MINOR0007 Returns OK

• Also set manufactuer ID is necessary, because the factory set of UUID is the same:

1. The factory ID is 65330 (decimal value) and the hexadecimal value is 1985
2. Send via serial port: AT + VID1985 Returns: OK

PWM Cotrol

• The first step to set the PWM frequency is 250Hz (frequency range is 50 - 4KHZ)
• AT command: AT + PWMFRE250 returns OK
• The second step turns on the PWM
• AT command: AT + PWMOPEN1 return OK (1 is not open to open the PWM, 2 is turned on)
• The third step to open the set PWM pulse width (4-way PWM output, so you can set the 4-way PWM pulse width)
• AT command: AT + PWM1PUS90 return OK to set PWM1 pulse width is 90%
• AT command: AT + PWM2PUS10 return OK to set PWM2 pulse width is 10%
• The following are PWM3 and PWM4 settings, not one by one here about
• The fourth step user can read the working status of PWM
• AT command: AT + PWMPUS return to the state, see the manual
• Step 5 Turn off the PWM function
• AT command: AT + PWMOPEN0 This module will turn off the PWM function, and if the PWRC pin is high
• Level, the module will enter the low-power mode,

iBeacon Sensor

• Step 1: Configure the module to iBeacon mode
• Note that the sensor function is only applied in the iBeacon mode, so you need to configure the iBeacon mode
• Send via serial port: AT + HOSTEN3 Returns: OK
• Step 2: Let the module restart
• Send via serial port: AT + RST means reset
• Step 3: Set the temperature to 33 degrees
• Send via serial port: AT + TEMP33 Returns: OK
• Step 4: Set the humidity value to 11%
• Send via serial port: AT + HUMID11 returns OK
• Step 5: Set the power of the sensor to 90%
• Send via serial port: AT + BATT90 returns OK
• Since the sensor function is based on the iBeacon application, if your sensor is numerous, the above two sensor commands
• Can not meet your product applications, you can use iBeacon related instructions to transmit your sensor data
• AT + STRUUID + 32-bit string length, please note that this 32-bit data format: Hexadecimal string
• AT + MAJOR + 4-bit string length, the string format: hexadecimal string
• AT + MINOR + 4-bit string length, the string format: hexadecimal string

Power Consumption Setup

• The default broadcast interval is the smallest, due to different user's product requirements, the power consumption of products have great requirements, so our module also considered this, the module can broadcast interval is set by AT command
• The default broadcast interval is: AT + ADVIN0 is 100 ms
• Users need to have certain requirements for power consumption can be set by AT + ADVIN broadcast interval
• The AT command broadcasts the time current
• AT + ADVIN0 100ms 0.6mA
• AT + ADVIN1 500ms 0.1mA
• AT + ADVIN2 750ms 0.05mA
• AT + ADVIN3 1000ms 0.02mA
• The above is set by the AT command, the user can also set the broadcast interval through the phone, not the longer the better the broadcast interval, the broadcast interval is too long will affect the connection time, is to be a long time to connect with the phone, the general set 100 or 500ms About the same, the sensor application can be set up a little longer, because no connection
• Connection interval settings
• Users can connect with the phone when the current can be set, you can AT command or phone to set the AT command can be set by: AT + NEIN to set
• The AT command broadcasts the time current
• AT + NEIN0 10ms 0.8mA
• AT + NEIN1 100ms 0.2mA
• AT + NEIN2 500ms 0.05mA
• The above is through the AT command to set the connection interval, the user can also set the connection interval through the phone, not the connection interval set the longer the better, but also depends on the user to determine the use of the scene, the longer the interval does not adapt to penetration, If the general requirements for the default interval can be, if only some control applications, or small data should be, then the connection interval can be set a little longer.

Master to Slave, two bluetooth mode

• Master-slave Bluetooth module communication refers to two Bluetooth modules communicate with each other, one for the host, a slave, they communicate with each other, the first module for the slave module, the second module is the host module
• The first step will host and slave module power and the module serial port and USB serial or MCU serial port connection, pay attention to the need to cross the serial line, connect the AT command to start debugging
• The second step will be the first module from the machine to open the radio, the default is to open the broadcast from the machine, but also by sending AT + ADVEN1 to open the broadcast
• Step 3: Set the commands of the main module
• 1) Set the module to host transparent mode, return OK to complete the set send command: AT + HOSTEN1 return OK
• 2) Set the module to restart
• Send: AT + RST
• 3) Scan the surrounding BLE command
• Send: T + SCAN1 Returns OK
• 4) Read the number of BLE Bluetooth scanned (up to 8 slaves)
• AT + GETDCD returns DEV: 1 means scanning to a device  
• 5) Read the slave MAC address of the scan list (0-7)
• Send: AT + RSLV0 Returns: MAC: e3435480
• 6) Connection scan list 0 device (0-7)
• Send: AT + CONNET0
• 7) Send the command to find out whether it is connected with the slave
• Send: AT + GETSTAT Returns: STS: 11 Indicates that the connection has been made    
• 8) The hardware judges whether it has been connected with the slave
• Module 6 pin for the connection status pin, the connection is successful for the low, not connected to high
• 9) host and slave connection is successful, you can transparently transfer data

Master/slave pair/binding mode for data tranmissoin

• Sets the command for the master module
• 1) Set the module to host transparent mode, return OK to complete the setup
• Send command: AT + HOSTEN1 returns OK
• 2) Set the module to restart
• Send: AT + RST
• 3) The host binds the slave MAC address
• Send the command: AT + BAND884AEA478140 to return OK
• 4) The hardware judges whether it has been connected with the slave
• Module 6 pin for the connection status pin, the connection is successful for the low, not connected to high
• 5) After the host and the slave connection is successful, you can pass through the data, and binding only once, the next power does not need to
• Time binding, later used as long as the binding of the slave in the host communication range, the host will automatically connect with the slave, the connection, they can be transparent between the data.
• 6) Unbind the slave
• Send: AT + CLRBAND Returns OK
• As a result of the binding from the machine, the host will have been connected with the binding from the machine, even if the machine is closed, the host will search around to see if there is bound from the machine, if there is to connect with it, After the host will no longer be bound with the slave to connect,
• Note: When the above host binds the MAC address of the slave, you need to know the MAC address of the slave. The MAC address of the slave can be read by AT + MAC.

Sensor read function

• Connect the serial port (RXD, TXD) of the USB serial or MCU to the module, and connect the PWRC pin of the module to the power supply (VCC, GND) of the module when sending commands using the serial port. , The supply voltage is 3.3V or 3V
• According to the above connection line, began to talk about the AT command operation
• Step 1: Configure the module as a host observer
• Send via serial port: AT + HOSTEN2 Returns: OK
• Step 2: Let the module restart
• Send via serial port: AT + RST means reset
• Through the above settings, the module has been configured for the host observer mode, then start the host machine to receive the data from the sensor, the host serial port to receive the sensor data format is as follows
• (+) Byte (byte) VID + 1 (byte) TEMP + 1 (byte) DATA format: 2 (bytes) Head + 6 (bytes) MAC + 1 (byte) RSSI + + 1 (bytes) BATT
• The user can identify their own sensor data through the VID, and then distinguish each sensor by MAC address
• Note: the data received by the host MAJOR, MINOR, VID, TEMP, HUMID, BATT corresponds to the slave transmission
• The data sent by the AT command in the sensor mode
• AT + MAJOR000A
• AT + MINOR0007
• AT + VID6677
• AT + TEMP44
• AT + TEMP44
• AT + BATT90

Replace your module by UUID

• For example, before you use the transparent module UUID service for the 0XFFF0, features UUID 0XFFF1,
• You only need to send these two commands to change the service UUID and feature UUID of our module.
• Send via serial port:
• AT + SVRUUIDFFF0 Returns: OK
• AT + CHRUUIDFFF1 Returns: OK