Loading files
This file is pinned to the selected release. Download the original to open it in your design tool.
/*
* Copyright 2012 Michael Ossmann <mike@ossmann.com>
* Copyright 2012 Jared Boone <jared@sharebrained.com>
* Copyright 2013 Benjamin Vernoux <titanmkd@gmail.com>
*
* This file is part of HackRF.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, Inc., 51 Franklin Street,
* Boston, MA 02110-1301, USA.
*/
#include "hackrf_core.h"
#include "rf_path.h"
#include "sgpio.h"
#include <libopencm3/lpc43xx/i2c.h>
#include <libopencm3/lpc43xx/cgu.h>
#include <libopencm3/lpc43xx/gpio.h>
#include <libopencm3/lpc43xx/scu.h>
#include <libopencm3/lpc43xx/ssp.h>
#define WAIT_CPU_CLOCK_INIT_DELAY (10000)
void delay(uint32_t duration)
{
uint32_t i;
for (i = 0; i < duration; i++)
__asm__("nop");
}
/* clock startup for Jellybean with Lemondrop attached
Configure PLL1 to max speed (204MHz).
Note: PLL1 clock is used by M4/M0 core, Peripheral, APB1. */
void cpu_clock_init(void)
{
/* use IRC as clock source for APB1 (including I2C0) */
CGU_BASE_APB1_CLK = CGU_BASE_APB1_CLK_CLK_SEL(CGU_SRC_IRC);
/* use IRC as clock source for APB3 */
CGU_BASE_APB3_CLK = CGU_BASE_APB3_CLK_CLK_SEL(CGU_SRC_IRC);
//FIXME disable I2C
/* Kick I2C0 down to 400kHz when we switch over to APB1 clock = 204MHz */
//i2c0_init(255);
/*
* 12MHz clock is entering LPC XTAL1/OSC input now. On
* Jellybean/Lemondrop, this is a signal from the clock generator. On
* Jawbreaker, there is a 12 MHz crystal at the LPC.
* Set up PLL1 to run from XTAL1 input.
*/
//FIXME a lot of the details here should be in a CGU driver
/* set xtal oscillator to low frequency mode */
CGU_XTAL_OSC_CTRL &= ~CGU_XTAL_OSC_CTRL_HF_MASK;
/* power on the oscillator and wait until stable */
CGU_XTAL_OSC_CTRL &= ~CGU_XTAL_OSC_CTRL_ENABLE_MASK;
/* Wait about 100us after Crystal Power ON */
delay(WAIT_CPU_CLOCK_INIT_DELAY);
/* use XTAL_OSC as clock source for BASE_M4_CLK (CPU) */
CGU_BASE_M4_CLK = (CGU_BASE_M4_CLK_CLK_SEL(CGU_SRC_XTAL) | CGU_BASE_M4_CLK_AUTOBLOCK(1));
/* use XTAL_OSC as clock source for APB1 */
CGU_BASE_APB1_CLK = CGU_BASE_APB1_CLK_AUTOBLOCK(1)
| CGU_BASE_APB1_CLK_CLK_SEL(CGU_SRC_XTAL);
/* use XTAL_OSC as clock source for APB3 */
CGU_BASE_APB3_CLK = CGU_BASE_APB3_CLK_AUTOBLOCK(1)
| CGU_BASE_APB3_CLK_CLK_SEL(CGU_SRC_XTAL);
cpu_clock_pll1_low_speed();
/* use PLL1 as clock source for BASE_M4_CLK (CPU) */
CGU_BASE_M4_CLK = (CGU_BASE_M4_CLK_CLK_SEL(CGU_SRC_PLL1) | CGU_BASE_M4_CLK_AUTOBLOCK(1));
/* use XTAL_OSC as clock source for PLL0USB */
CGU_PLL0USB_CTRL = CGU_PLL0USB_CTRL_PD(1)
| CGU_PLL0USB_CTRL_AUTOBLOCK(1)
| CGU_PLL0USB_CTRL_CLK_SEL(CGU_SRC_XTAL);
while (CGU_PLL0USB_STAT & CGU_PLL0USB_STAT_LOCK_MASK);
/* configure PLL0USB to produce 480 MHz clock from 12 MHz XTAL_OSC */
/* Values from User Manual v1.4 Table 94, for 12MHz oscillator. */
CGU_PLL0USB_MDIV = 0x06167FFA;
CGU_PLL0USB_NP_DIV = 0x00302062;
CGU_PLL0USB_CTRL |= (CGU_PLL0USB_CTRL_PD(1)
| CGU_PLL0USB_CTRL_DIRECTI(1)
| CGU_PLL0USB_CTRL_DIRECTO(1)
| CGU_PLL0USB_CTRL_CLKEN(1));
/* power on PLL0USB and wait until stable */
CGU_PLL0USB_CTRL &= ~CGU_PLL0USB_CTRL_PD_MASK;
while (!(CGU_PLL0USB_STAT & CGU_PLL0USB_STAT_LOCK_MASK));
/* use PLL0USB as clock source for USB0 */
CGU_BASE_USB0_CLK = CGU_BASE_USB0_CLK_AUTOBLOCK(1)
| CGU_BASE_USB0_CLK_CLK_SEL(CGU_SRC_PLL0USB);
/* Switch peripheral clock over to use PLL1 (204MHz) */
CGU_BASE_PERIPH_CLK = CGU_BASE_PERIPH_CLK_AUTOBLOCK(1)
| CGU_BASE_PERIPH_CLK_CLK_SEL(CGU_SRC_PLL1);
/* Switch APB1 clock over to use PLL1 (204MHz) */
CGU_BASE_APB1_CLK = CGU_BASE_APB1_CLK_AUTOBLOCK(1)
| CGU_BASE_APB1_CLK_CLK_SEL(CGU_SRC_PLL1);
/* Switch APB3 clock over to use PLL1 (204MHz) */
CGU_BASE_APB3_CLK = CGU_BASE_APB3_CLK_AUTOBLOCK(1)
| CGU_BASE_APB3_CLK_CLK_SEL(CGU_SRC_PLL1);
}
/*
Configure PLL1 to low speed (48MHz).
Note: PLL1 clock is used by M4/M0 core, Peripheral, APB1.
This function shall be called after cpu_clock_init().
This function is mainly used to lower power consumption.
*/
void cpu_clock_pll1_low_speed(void)
{
uint32_t pll_reg;
/* Configure PLL1 Clock (48MHz) */
/* Integer mode:
FCLKOUT = M*(FCLKIN/N)
FCCO = 2*P*FCLKOUT = 2*P*M*(FCLKIN/N)
*/
pll_reg = CGU_PLL1_CTRL;
/* Clear PLL1 bits */
pll_reg &= ~( CGU_PLL1_CTRL_CLK_SEL_MASK | CGU_PLL1_CTRL_PD_MASK | CGU_PLL1_CTRL_FBSEL_MASK | /* CLK SEL, PowerDown , FBSEL */
CGU_PLL1_CTRL_BYPASS_MASK | /* BYPASS */
CGU_PLL1_CTRL_DIRECT_MASK | /* DIRECT */
CGU_PLL1_CTRL_PSEL_MASK | CGU_PLL1_CTRL_MSEL_MASK | CGU_PLL1_CTRL_NSEL_MASK ); /* PSEL, MSEL, NSEL- divider ratios */
/* Set PLL1 up to 12MHz * 4 = 48MHz. */
pll_reg |= CGU_PLL1_CTRL_CLK_SEL(CGU_SRC_XTAL)
| CGU_PLL1_CTRL_PSEL(0)
| CGU_PLL1_CTRL_NSEL(0)
| CGU_PLL1_CTRL_MSEL(3)
| CGU_PLL1_CTRL_FBSEL(1)
| CGU_PLL1_CTRL_DIRECT(1);
CGU_PLL1_CTRL = pll_reg;
/* wait until stable */
while (!(CGU_PLL1_STAT & CGU_PLL1_STAT_LOCK_MASK));
/* Wait a delay after switch to new frequency with Direct mode */
delay(WAIT_CPU_CLOCK_INIT_DELAY);
}
/*
Configure PLL1 (Main MCU Clock) to max speed (204MHz).
Note: PLL1 clock is used by M4/M0 core, Peripheral, APB1.
This function shall be called after cpu_clock_init().
*/
void cpu_clock_pll1_max_speed(void)
{
uint32_t pll_reg;
/* Configure PLL1 to Intermediate Clock (between 90 MHz and 110 MHz) */
/* Integer mode:
FCLKOUT = M*(FCLKIN/N)
FCCO = 2*P*FCLKOUT = 2*P*M*(FCLKIN/N)
*/
pll_reg = CGU_PLL1_CTRL;
/* Clear PLL1 bits */
pll_reg &= ~( CGU_PLL1_CTRL_CLK_SEL_MASK | CGU_PLL1_CTRL_PD_MASK | CGU_PLL1_CTRL_FBSEL_MASK | /* CLK SEL, PowerDown , FBSEL */
CGU_PLL1_CTRL_BYPASS_MASK | /* BYPASS */
CGU_PLL1_CTRL_DIRECT_MASK | /* DIRECT */
CGU_PLL1_CTRL_PSEL_MASK | CGU_PLL1_CTRL_MSEL_MASK | CGU_PLL1_CTRL_NSEL_MASK ); /* PSEL, MSEL, NSEL- divider ratios */
/* Set PLL1 up to 12MHz * 8 = 96MHz. */
pll_reg |= CGU_PLL1_CTRL_CLK_SEL(CGU_SRC_XTAL)
| CGU_PLL1_CTRL_PSEL(0)
| CGU_PLL1_CTRL_NSEL(0)
| CGU_PLL1_CTRL_MSEL(7)
| CGU_PLL1_CTRL_FBSEL(1);
CGU_PLL1_CTRL = pll_reg;
/* wait until stable */
while (!(CGU_PLL1_STAT & CGU_PLL1_STAT_LOCK_MASK));
/* Wait before to switch to max speed */
delay(WAIT_CPU_CLOCK_INIT_DELAY);
/* Configure PLL1 Max Speed */
/* Direct mode: FCLKOUT = FCCO = M*(FCLKIN/N) */
pll_reg = CGU_PLL1_CTRL;
/* Clear PLL1 bits */
pll_reg &= ~( CGU_PLL1_CTRL_CLK_SEL_MASK | CGU_PLL1_CTRL_PD_MASK | CGU_PLL1_CTRL_FBSEL_MASK | /* CLK SEL, PowerDown , FBSEL */
CGU_PLL1_CTRL_BYPASS_MASK | /* BYPASS */
CGU_PLL1_CTRL_DIRECT_MASK | /* DIRECT */
CGU_PLL1_CTRL_PSEL_MASK | CGU_PLL1_CTRL_MSEL_MASK | CGU_PLL1_CTRL_NSEL_MASK ); /* PSEL, MSEL, NSEL- divider ratios */
/* Set PLL1 up to 12MHz * 17 = 204MHz. */
pll_reg |= CGU_PLL1_CTRL_CLK_SEL(CGU_SRC_XTAL)
| CGU_PLL1_CTRL_PSEL(0)
| CGU_PLL1_CTRL_NSEL(0)
| CGU_PLL1_CTRL_MSEL(16)
| CGU_PLL1_CTRL_FBSEL(1)
| CGU_PLL1_CTRL_DIRECT(1);
CGU_PLL1_CTRL = pll_reg;
/* wait until stable */
while (!(CGU_PLL1_STAT & CGU_PLL1_STAT_LOCK_MASK));
}
void ssp1_init(void)
{
/*
* Raise ADF4158 CE pin to de-select the device
*/
gpio_clear(PORT_ADF_CE, PIN_ADF_CE);
gpio_clear(PORT_ADF_LE, PIN_ADF_LE);
/* Configure SSP1 Peripheral (to be moved later in SSP driver) */
scu_pinmux(SCU_SSP1_MISO, (SCU_SSP_IO | SCU_CONF_FUNCTION5));
scu_pinmux(SCU_SSP1_MOSI, (SCU_SSP_IO | SCU_CONF_FUNCTION5));
scu_pinmux(SCU_SSP1_SCK, (SCU_SSP_IO | SCU_CONF_FUNCTION1));
ssp1_set_mode_16bit();
}
void ssp1_set_mode_16bit(void)
{
/* FIXME speed up once everything is working reliably */
/*
// Freq About 0.0498MHz / 49.8KHz => Freq = PCLK / (CPSDVSR * [SCR+1]) with PCLK=PLL1=204MHz
const uint8_t serial_clock_rate = 32;
const uint8_t clock_prescale_rate = 128;
*/
// Freq About 4.857MHz => Freq = PCLK / (CPSDVSR * [SCR+1]) with PCLK=PLL1=204MHz
const uint8_t serial_clock_rate = 21;
const uint8_t clock_prescale_rate = 2;
ssp_init(SSP1_NUM,
SSP_DATA_16BITS,
SSP_FRAME_SPI,
SSP_CPOL_0_CPHA_0,
serial_clock_rate,
clock_prescale_rate,
SSP_MODE_NORMAL,
SSP_MASTER,
SSP_SLAVE_OUT_ENABLE);
}
void ssp1_set_mode_8bit(void)
{
/* FIXME speed up once everything is working reliably */
/*
// Freq About 0.0498MHz / 49.8KHz => Freq = PCLK / (CPSDVSR * [SCR+1]) with PCLK=PLL1=204MHz
const uint8_t serial_clock_rate = 32;
const uint8_t clock_prescale_rate = 128;
*/
// Freq About 4.857MHz => Freq = PCLK / (CPSDVSR * [SCR+1]) with PCLK=PLL1=204MHz
const uint8_t serial_clock_rate = 21;
const uint8_t clock_prescale_rate = 2;
ssp_init(SSP1_NUM,
SSP_DATA_8BITS,
SSP_FRAME_SPI,
SSP_CPOL_0_CPHA_0,
serial_clock_rate,
clock_prescale_rate,
SSP_MODE_NORMAL,
SSP_MASTER,
SSP_SLAVE_OUT_ENABLE);
}
void pin_setup(void) {
/* GPIO pinmuxes */
scu_pinmux(SCU_PINMUX_LED1, SCU_GPIO_NOPULL | SCU_CONF_FUNCTION4);
scu_pinmux(SCU_ADC_NOE, SCU_GPIO_NOPULL);
scu_pinmux(SCU_PA_OFF, SCU_GPIO_NOPULL | SCU_CONF_FUNCTION4);
scu_pinmux(SCU_MIX_ENBL, SCU_GPIO_NOPULL | SCU_CONF_FUNCTION4);
scu_pinmux(SCU_ADF_TXDATA, SCU_GPIO_NOPULL);
scu_pinmux(SCU_ADF_CE, SCU_GPIO_FAST);
scu_pinmux(SCU_ADF_LE, SCU_GPIO_FAST);
/* Configure P2_3 as USB0_PPWR */
//scu_pinmux(SCU_OTG_USBV, SCU_CONF_FUNCTION7);
/* Configure all GPIO as Input (safe state) */
GPIO0_DIR = 0;
GPIO1_DIR = 0;
GPIO2_DIR = 0;
GPIO3_DIR = 0;
GPIO4_DIR = 0;
GPIO5_DIR = 0;
GPIO6_DIR = 0;
GPIO7_DIR = 0;
rf_disable();
GPIO5_DIR |= (PIN_LED1);
GPIO0_DIR |= (PIN_ADC_NOE);
GPIO5_DIR |= (PIN_PA_OFF | PIN_MIX_ENBL);
GPIO1_DIR |= (PIN_ADF_LE | PIN_ADF_CE | PIN_ADF_TXDATA);
/* Configure SSP1 Peripheral (to be moved later in SSP driver) */
//scu_pinmux(SCU_SSP1_MISO, (SCU_SSP_IO | SCU_CONF_FUNCTION5));
scu_pinmux(SCU_SSP1_MOSI, (SCU_SSP_IO | SCU_CONF_FUNCTION5));
scu_pinmux(SCU_SSP1_SCK, (SCU_SSP_IO | SCU_CONF_FUNCTION1));
//scu_pinmux(SCU_SSP1_SSEL, (SCU_SSP_IO | SCU_CONF_FUNCTION1));
sgpio_configure_pin_functions();
}
7f5f835eeThis file is pinned to the selected release. Download the original to open it in your design tool.