Loading files
This file is pinned to the selected release. Download the original to open it in your design tool.
# Step 1: Basic Motor Control Setup
This is the foundation of the Fastbot - a simple differential drive robot controlled via Arduino and ROS.
## Hardware Components
### Required Parts
1. **Arduino Microcontroller** (Nano or compatible)
2. **2x TT DC Motors with Encoders**
- [Yahboom Encoder TT Motor](https://category.yahboom.net/products/encoder-tt-motor?variant=39554242412628)
- 6V DC motors with built-in encoders
3. **L298N Motor Driver**
- Dual H-bridge motor driver
- Can drive 2 DC motors
- Built-in 5V regulator
4. **Power Supply**
- 7-12V battery pack for motors (in my case ovonic 2200mAh 11.1V)
- USB power for Arduino
5. **Jumper Wires**
## Wiring

### L298N to Arduino Connections
| L298N Pin | Arduino Pin | Description |
| --------- | ------------ | ------------------------------ |
| IN1 | D10 | Left motor direction forward |
| IN2 | D6 | Left motor direction backward |
| IN3 | D5(opposite) | Right motor direction forward |
| IN4 | D9(opposite) | Right motor direction backward |
**Note**: "opposite" means the wiring is swapped in the Arduino code - the forward pin connects to the backward control in code, and vice versa. This is done to account for the right motor being mounted in reverse orientation.
### Motor Encoder Connections
| Encoder Pin | Arduino Pin | Description |
| --------------------- | ------------ | ------------------ |
| Left motor Encoder A | D2 | Interrupt pin |
| Left motor Encoder B | D3 | Direction sensing |
| Right motor Encoder A | A5(opposite) | Interrupt pin |
| Right motor Encoder B | A4(opposite) | Direction sensing |
| Encoder VCC | 5V | Power for encoders |
| Encoder GND | GND | Ground |
**Note**: "opposite" means the wiring is swapped in the Arduino code - encoder A wire connects to the B pin in code, and encoder B wire connects to the A pin in code. This is done to account for the right motor being mounted in reverse orientation.
### Power Connections
1. Connect battery pack (+) to L298N 12V input
2. Connect battery pack (-) to L298N GND
3. Connect motors to L298N motor outputs (OUT1/OUT2 for left motor, OUT3/OUT4 for right motor (always first +, second -))
## Software Setup
### 1. Setup Arduino Firmware
The ros_arduino_bridge provides Arduino firmware that turns your Arduino into a motor controller with a serial interface. This allows a higher-level computer (like a Raspberry Pi running ROS) to communicate with the Arduino to control motors and read encoders.
**Repository**: [https://github.com/joshnewans/ros_arduino_bridge](https://github.com/joshnewans/ros_arduino_bridge)
```bash
# Clone the repository
git clone https://github.com/joshnewans/ros_arduino_bridge.git
```
### 2. Upload Arduino Sketch
1. Open the Arduino IDE
2. Navigate to the cloned repository and open `ROSArduinoBridge/ROSArduinoBridge.ino`
3. Upload to your Arduino Nano
**Note**: This firmware runs on the Arduino. Later, you'll connect this Arduino to a Raspberry Pi (or other computer) running ROS, which will send commands over serial to control the robot.
## Testing
### Serial Communication Test
Before running ROS, test the Arduino communication using a serial terminal.
**Using Serial Tool**: [https://serialtool.com/\_en/index.php](https://serialtool.com/_en/index.php)
1. Connect your Arduino via USB
2. Open Serial Tool in your browser
3. Configure the connection:
- **Port**: Select the correct USB port (usually `/dev/ttyUSB0` or `/dev/ttyACM0` on Linux, `COM1` or similar on Windows)
- **Baud Rate**: 57600
4. Click "Connect"
**Test Commands**:
- `e` - Read encoder values
- `r` - Reset encoders
- `o 100 100` - Move motors (open loop, direct PWM)
- `m 100 100` - Move motors (closed loop, PID control)
## Resources
- [ros_arduino_bridge Documentation](https://github.com/joshnewans/ros_arduino_bridge)
- [L298N Datasheet](https://www.sparkfun.com/datasheets/Robotics/L298_H_Bridge.pdf)
- [TT Motor Specifications](https://category.yahboom.net/products/encoder-tt-motor?variant=39554242412628)
83abc844cThis file is pinned to the selected release. Download the original to open it in your design tool.