Stackable, parametric 3D-printable desktop rack for the NVIDIA DGX Spark (OpenSCAD)
Loading README and project media…
A modular, 3D-printable desktop rack for the NVIDIA DGX Spark. Trays click together like drawers; the top Spark sits in a slim walls-less cap. When you get another Spark, print one more tray and move the cap up. No hardware, no separate base or lid.
Also published on MakerWorld.
Compatibility note: This design was fit-tested on an NVIDIA DGX Spark Founders Edition and a Gigabyte DGX Spark. Other variants (Dell, MSI, Acer, ASUS) may differ in dimensions — you may need to revise the pedestal measurements and tweak the clearance parameters before printing.

The Spark stands on a rounded-rectangle pedestal (~111 × 101 mm at the desk, flaring to 128.6 × 118.6 mm) that is smaller than its 150 × 150 shell. Each tray floor has a funnel-shaped opening that mirrors the pedestal's measured flare profile: the pedestal nests into it, the chassis rests on the surrounding rim, and the funnel wedges the unit on center — locked in plan with ~0.4 mm of play, no retaining lips.
Dovetail rails run front-to-back along the top of each side wall, with matching grooves in the underside. A new tray (Spark already inside) slides onto the stack from the front and registers against a blind stop at the rear, so trays self-align flush.
Every dovetail joint snaps shut: a cantilever finger cut into each groove's inner cheek carries a dome that clicks 0.8 mm deep into a pocket on the rail flank as the joint hits its stop. The finger is a real spring (not just joint slack), so the click is crisp and the hold is solid; a firm pull cams it back out. It sits at the groove's blind end, so it only rubs the rail for the last ~4.5 mm of the slide — and all its cuts face the inside of the joint, so the outer walls stay completely solid. No loose parts:

The cap is the top of the stack: the same funnel floor on 8 mm bands with the same grooves and snap fingers, but no walls, rails or windows — the top Spark sits fully exposed. Spark count grows? Print one more tray, slide the cap onto it.
The rails are inset 10 mm from both faces, so the feet sit with an equal reveal at each end.
The front and rear faces are completely open. The Spark's intakes are on the top and bottom edges of its front face and it exhausts out the rear; a 10 mm air gap above each unit keeps the top intake breathing under the next tray, and the pedestal opening leaves the underside almost fully exposed.
The floor is 6 mm thick — the same as the pedestal height, so the pedestal nests exactly flush with the tray underside.
Two runner feet slide into the bottom tray's (otherwise unused) underside dovetail grooves and lift the whole stack 10 mm off the desk, giving the bottom Spark's dust-filter vent free air underneath.
| DGX Spark unit | 150 × 150.75 × 51.5 mm, 1.2 kg (measured from reference STL; teardowns report 51.2 mm height) |
| Floor funnel | 111.8 × 101.8 mm at the bottom → 130.2 × 120.2 mm at the rim (measured flare profile + 0.4 mm) |
| Tray footprint | 175.61 × 152.25 mm |
| Tray height | 65.5 mm (61.5 mm stack pitch + 4 mm rail) |
| Tray volume | ~204 cm³ (≈ 125–145 g ABS per tray at 3 walls / 10 % infill; ≈ 150–170 g in PETG) |
| Roof cap | 175.61 × 152.25 × 8 mm, ~81 cm³ |
| Runner foot | 12 × 132.25 × 14 mm, ~19 cm³ each (print 2) |
| Snap lock | Ø3.2 dome on a 26 mm finger, 0.8 mm engagement |
| Desk lift | 10 mm (foot_h) |
Fits any 180 × 160 mm or larger print bed. A stack of N Sparks = (N − 1) trays + 1 cap + 2 feet.
Material: ABS or PC recommended — a loaded Spark runs warm continuously, and both hold up well under sustained heat and load; this design was printed and fit-tested in ABS. PETG works but has noticeably less heat resistance. Avoid PLA — it creeps under sustained heat + load.

See Bambu Lab's filament guide for a full comparison.
Orientation: as modeled — base on the bed, rails up. Supports needed on the dovetail rail overhangs — at ~69° from horizontal they're steep enough that most slicers/printers won't bridge them cleanly without support material; the groove roofs are short bridges and print fine unsupported.
Walls/infill: 3 perimeters, 10 % gyroid infill, 0.2 mm layers. This is already generous for the load (a full stack puts a few kg across thousands of mm² of material); more walls/infill just costs filament.
First layer: heavy squish (elephant's foot) tightens the groove openings on the underside. Use your slicer's elephant-foot compensation (~0.2 mm) or expect to lightly deburr the groove edges on the first print.
Bridging: the side-window top edge bridges ~59 mm inside the wall (the 45° window corners are self-supporting), and the funnel's relief bore forms a short internal ledge ring that bridges over the funnel. Both are cosmetic and touch nothing; any printer with part cooling copes.
To remove a level: pull it firmly along the slide until the snap fingers release, slide it off, and lift the Spark out.
Everything is parametric in spark-rack.scad (all parameters documented at
the top of the file). The knobs you may need:
dt_clear (default 0.25 mm) — dovetail sliding clearance, applied as a
true normal offset so the gap is uniform along the whole flank. Slide too
tight → 0.3–0.35; sloppy → 0.15–0.2. Any new tray must mate with your
existing ones, so pick a value and keep it forever.
ped_clear (default 0.4 mm per side, normal to the pedestal surface) —
funnel clearance. If the Spark doesn't fully seat, go 0.5–0.6; the funnel
keeps self-centering either way.
fin_depth (default 0.8 mm) — snap engagement depth: the click/hold
strength knob. Weak → 0.9–1.0; too hard to release → 0.6. fin_l
(26 mm) is the finger length — longer = softer spring.
To try the snap lock before printing full parts, print the two tiny
coupons (spark-rack-testlock-groove.stl + spark-rack-testlock-rail.stl,
~7 g each, sliced straight out of the real cap/foot geometry): put the
rail coupon on the table rail-up, slide the groove coupon over it until
it clicks at the stop, and pull it back off. Tune fin_depth, re-export,
repeat — a coupon pair prints in well under an hour.
air_gap (default 10 mm) — thermal headroom above each unit (NVIDIA's
own two-unit bundle stacks the Sparks with zero gap).
foot_h (default 10 mm) — desk lift of the runner feet.
openscad -o spark-rack-tray.stl spark-rack.scad
openscad -o spark-rack-cap.stl -D 'part="cap"' spark-rack.scad
openscad -o spark-rack-foot.stl -D 'part="foot"' spark-rack.scad
# assembly preview (feet + tray + cap):
openscad -o stack2.stl -D 'part="stack2"' spark-rack.scad
nvidia-dgx-spark-rack-tray.3mf is a Bambu Studio project export (P1S/ABS)
with the print profile embedded, for MakerWorld's print-profile upload.
tests/run.sh runs the boolean interference suite (8 checks): seated
tray-on-tray, cap-on-tray and feet joints must be empty; a joint displaced
3 mm must collide only at the snap dome (the lock engaging); the 1:1 Spark
reference STL must rest with zero interference, collide when pushed 0.5 mm
below resting (cannot fall through), stay free shifted 0.35 mm and collide
shifted 0.6 mm (the funnel locking in plan). All pass with OpenSCAD
2023.09.11. Independent slicing measurements additionally confirmed a
uniform 0.27 mm/side dovetail clearance, 0.25 mm vertical, and that the
unit sits centered (12.8 mm side margins; 0.375 mm front/rear offset from
the reference model's foam bulge). tests/render_views.py regenerates the
preview images.
The fit checks use the 1:1 Spark model by SchwickSchwimmer
(MakerWorld 2107931,
Printables 1512927,
CC BY-NC-SA — not included in this repo; download it as
dgx-spark-reference.stl). To re-run the fit test, seat it at
translate([ow/2, td/2, base_t + 22.975]) (its chassis underside plane lies
22.975 mm above its own Z origin) and intersect with tray().
The pedestal geometry comes solely from the community reference model (overall dims match NVIDIA's spec and teardown measurements to within ~0.5 mm, but nobody has published official CAD). Flip your Spark over and check with a ruler:
If your unit measures outside that, adjust ped_w/ped_d and re-export.
CC BY-NC-SA 4.0 — a community model: print it, modify it, remix it and share your versions freely, just credit jvr0x, keep the same license on derivatives, and don't use it commercially (no selling files or prints). (Matches the MakerWorld listing license.) The 1:1 Spark reference model used for fit testing is separately licensed CC BY-NC-SA by its author and is not included here.
If these designs have been useful and you'd like to support my work, you can buy me a coffee. Any contribution is appreciated.
Solana (SOL/USDC):
CwaKF7oNeca9r9PWq4KVf4vmaf158S2SrXRVn8U2sng5
Ethereum (ETH/USDC):
0xc968c47eAb277e06B96B6d9bDf9Df8ef5242E28A
Bitcoin (BTC):
bc1qveau6va70eaqtvqkxekvfaxhpwzmfqlw0jhyaa