BLEKey

by Mark Baseggio and Eric Evenchick

BLEKey is a tool designed to demonstrate the risks of using the Wiegand protocol.

Here's a video of us talking about the BLEKey at Blackhat USA 2015.

You can get BLEKey here: http://store.cantact.io/products/blekey-1?variant=18261748871 ANY OTHER STORE/SITE IS UNOFFICIAL

Building

1. Download the GNU ARM Embedded Toolchain for your OS (gcc-arm-none-eabi-4_9-2015q1 was used to build this version): https://launchpad.net/gcc-arm-embedded/+download
2. Clone the repo: git clone https://github.com/linklayer/BLEKey.git
3. Edit the Makefile.posix file in the BLEKey/gcc/ directory and make sure the path to the downloaded ARM toolchain is correct.
4. Change to the BLEKey/gcc directory and run make

If you have a Segger hooked up to the board you can also run:

• make erase to erase the nrf
• make flash-sd to flash the soft device
• make flash to flash the compiled hex

Flashing

Firmware Over the Air (FOTA)

We've included a file in the /firmware folder called super.hex. This firmware has a bootloader included that allows the BLEKey to be flashed from a cell phone by shorting the first and last pins of the P2 port, and inserting a battery. The firmware update has been tested on the Android platform using the Nordic Master Control Panel tool.

We've created a video to demonstrate the process.

MacOS or Linux

To flash the softdevice and BLEKey firmware from the CLI you can use JLinkExe which is provided in the Segger Software

The BLEKey requires a softdevice (for BLE) and the blekey firmware. These can be flashed using the commands below:

$ /usr/bin/JLinkExe -device nrf51822_xxaa -if swd -speed 4000

J-Link>loadbin s110_nrf51822_7.0.0_softdevice.bin 0
J-Link>loadbin blekey_s110_xxaa.hex 0x16000
J-Link>r
J-Link>g

Erasing:

J-Link>w4 4001e504 2
J-Link>w4 4001e50c 1

If you prefer a GUI you can always use rknrfgo

The cheatsheet above is ripped from Nordic's blog

Windows

Use tools from Nordic.

Using BLEKey

BLE Characteristics

Service	Characteristic	Function
0xABCD	0xAAAA	Read Last Cards
0xABCD	0xBBBB	Replay Card
0xABCD	0xCCCC	Send Data (Data)
0xABCD	0xDDDD	Send Data (Length)

Client

There is a BLEKey client in the client/ directory of the git repo. See readme.md and requirements.txt for more information on its use.

Phones/Tablets

A client is planned. Until then download any BLE utility that can read/write BLE characteristics. See below for more information on specific characteristics.

CLI (Linux)

Find your Bluetooth device with hcitool dev scan for BLEKey with hcitool -i <dev> lescan

Start an interactive connection to BLEKey

Last three Wiegand cards are stored in the 0x000b handle. Currently to cause BLEKey to send out the last read card on the Wiegand lines write to 0x000d

[blark@archvm blekey]$ sudo gatttool -t random -b D4:34:E8:CA:6F:6A -I
[D4:34:E8:CA:6F:6A][LE]> connect
Attempting to connect to D4:34:E8:CA:6F:6A
Connection successful
[D4:34:E8:CA:6F:6A][LE]> characteristics
handle: 0x0002, char properties: 0x0a, char value handle: 0x0003, uuid: 00002a00-0000-1000-8000-00805f9b34fb
handle: 0x0004, char properties: 0x02, char value handle: 0x0005, uuid: 00002a01-0000-1000-8000-00805f9b34fb
handle: 0x0006, char properties: 0x02, char value handle: 0x0007, uuid: 00002a04-0000-1000-8000-00805f9b34fb
handle: 0x000a, char properties: 0x02, char value handle: 0x000b, uuid: 0000aaaa-0000-1000-8000-00805f9b34fb
handle: 0x000c, char properties: 0x08, char value handle: 0x000d, uuid: 0000bbbb-0000-1000-8000-00805f9b34fb
handle: 0x000e, char properties: 0x08, char value handle: 0x000f, uuid: 0000cccc-0000-1000-8000-00805f9b34fb
handle: 0x0010, char properties: 0x0a, char value handle: 0x0011, uuid: 0000dddd-0000-1000-8000-00805f9b34fb
handle: 0x0013, char properties: 0x12, char value handle: 0x0014, uuid: 00002a19-0000-1000-8000-00805f9b34fb
handle: 0x0017, char properties: 0x02, char value handle: 0x0018, uuid: 00002a29-0000-1000-8000-00805f9b34fb
[D4:34:E8:CA:6F:6A][LE]> char-write-req d 01
Characteristic value was written successfully
[D4:34:E8:CA:6F:6A][LE]> char-read-hnd b
Characteristic value/descriptor: 22 bd 58 60 7c 26 00 24 47 60 85 08 37 00 24 47 60 85 08 37 00 00 
[D4:34:E8:CA:6F:6A][LE]>

You can also just use gatttool from the command line to yell BLEKey to send Wiegand data (replace with the address of your device):

sudo gatttool -t random -b D4:34:E8:CA:6F:6A --char-write-req -a 0x000d -n 01

Notes:

• Bluetooth Explorer is in the Hardware IO Tools from Apple it's probably the best BLE utility for Mac.

Pinouts

Harware rev. 0 code name Acamas

Pin	Function
0	Data 0 in
1	Data 1 in
2	Data 0 ctl
3	Data 1 ctl
9	Serial
11	Serial
26	Xtal 1
27	Xtal 2
28	GPIO
29	GPIO
35	DIO
36	CLK

Hardware rev. 1 Agapenor

Pinouts are identical to Acamas unless otherwise noted.

Pin	Function
0	Data 0 in
7	Data 1 in
8	GPIO
20	LED0

P1 - Programming port (square solder mask pin 0)

Pin	Function
0	Vcc
1	DIO
2	CLK
3	Gnd

P2 - Serial/GPIO port (square solder mask pin 0)

Pin	Function
0	GPIO (Tx)
1	DATA0
2	DATA1
3	Gnd