Loading project Things
A Raspberry Pi 5-channel PWM, PT100 and ADXL345 board.
Loading README and project media…
A Raspberry Pi 5-channel PWM, PT100 and ADXL345 board. Should work on any Pi2/3/4
I was looking to add on more controllable fans to my 3D printer. The SKR was maxxed out even just a simple controllable fan, let alone PWM. Klipper supports multiple MCU's, including the Raspberry Pi so adding this to the Pi was a simple way to tackle the problem.
With a bit of spare board space (it was tight) I also fit some space to accommodate PT100 modules, so I could have a nice place to put mine.
Power the Raspberry Pi via the 5V input
You MUST power the Pi via this board. Do not connect any other power source (USB, PoE hat, battery backup hat) to the Pi when using this board.
5 PWM outputs (via MOSFETs with external flyback diodes)
Independant voltages for each fan - 5V or anything up 24V
Cutout for a 25mmx25mm fan to cool the Pi if desired
Support for Adafruit's PT100 amplifier board OR a PT100 Stepstick (available on AliExpress/etc)
Convenient header for an ADXL345 accelerometer to measure resonance in Klipper
The design is fully open source, and you are welcome to build this yourself. If you would like to buy a kit or fully assembled version, you can buy it on my Tindie store, Greg's Tinker Town. The kit is exclusive through-hole components.
The main board itself is rather sturdy, but using standoffs would be an extra measure to keep the board secure.
If using the Adafruit board, standoffs for that board are recommended.
Note that the input header will only accept the smallest (white) ferrules. Unfortunately there is minimal space on the board to accomodate a larger screw terminal without removing a channel.
The header supports either a 2x3 or 2x4 pin header. The 2x4 header can accomadate previously designed 2x4 headers that plugged directly in the Raspberry Pi header. The two 3V3 pins are linked so you can use either to power the ADXL345.
Note that if you are using a 4-wire thermistor, plugging in the accelerometer could be challenging. You may need to remove the thermistor temporarily for accelerometer tuning.
First, give a good read to Klipper documentation on Raspberry Pi as a secondary MCU
Then, we can reference the sample configuration provided and come up with the sample config files located in this repository.
The board was designed to power fans, not heavy loads or heaters. The designed but un-tested recommendations are a maximum of 750mA per channel, and a total maximum of 3A. Most fans operate between 50mA and 300mA. If you are going beyond this, you would be wise to review the trace widths and measure thermals to ensure you are comfortable with the results.
The Pi has 2 SPI busses. big p4ppa uses SPI1 for the PT100 board, and SPI0 for the ADXL accelerometer. Note that these pin arrangements are suited to the intended modules, but are otherwise just SPI breakouts if you want to use them for other purposes. Also, if you want to solder a Pi stacking header and use another board on top of this one, you can make a note of which SPI bus your additional board uses and avoid using it on big p4ppa. Fitment is not guaranteed for additional boards stacked on top.
Generally speaking it's hard to find 24V fans in 25mm x 25mm size. There are lots of 5V or 12V options. If you choose 5V, you may wish to run the fan at full speed for electrical noise considerations, as it is sharing the 5V of the Pi. As a result, choose your fan accordingly rather then buying something too strong and needing PWM to slow it down.
The SKR 1.4 already supports Neopixel LED's. It had to be cut due to board space.
Apologies for the KiCad layout. To be honest, it feels like KiCad v6 is so close, I haven't invested much effort. V6 will bundle symbols with the schematic which will be a huge step forward. Gerber's are there if you want to send them off to a fab.