Loading files
This file is pinned to the selected release. Download the original to open it in your design tool.
{
"generatedAt": "2026-08-15T13:14:48",
"measuredAgainst": {
"gitHead": "f9f2d4b",
"gitDirty": true,
"gitDirtyPaths": [
"examples/hydrate-coaster/boards/main.board.json",
"examples/hydrate-coaster/boards/main.circuit.json",
"examples/hydrate-coaster/boards/main.tsx",
"examples/hydrate-coaster/boards/main_fab/board.glb",
"examples/hydrate-coaster/boards/main_fab/bom.csv",
"examples/hydrate-coaster/boards/main_fab/cpl.csv",
"examples/hydrate-coaster/boards/main_fab/gerbers.zip",
"examples/hydrate-coaster/boards/main_fab/kicad-project.zip",
"examples/hydrate-coaster/boards/main_review/_pcb.png",
"examples/hydrate-coaster/boards/main_review/_pcb.svg",
"examples/hydrate-coaster/boards/main_review/_schematic.png",
"examples/hydrate-coaster/boards/main_review/_schematic.svg",
"work/"
],
"toolchain": {
"tscircuit": "0.0.2279",
"checks": "0.0.152",
"kicadCli": "10.0.5"
},
"verifyBlockingKinds": [
"dc_led_current",
"dc_rail_overload",
"dfa_board_size",
"dfa_bottom_side",
"dfa_courtyard_overlap",
"dfa_off_board",
"dfa_pin_pitch",
"gerber_drill_empty",
"gerber_drill_missing",
"gerber_drill_plating_mismatch",
"gerber_drill_size_mismatch",
"gerber_missing_layer",
"gerber_outline_empty",
"gerber_outline_mismatch",
"gerber_pad_masked_over",
"gerber_pad_missing",
"gerber_scale_mismatch",
"gerber_trace_width",
"gerber_unreadable",
"netclass_trace_width",
"thermal_resistor_power"
],
"verifyEscalatedKinds": [
"gerber_silk_line_width",
"review_debug_unreachable"
],
"checkSetHash": "e73558f0fc6f"
},
"tier": "default",
"cellsBuilt": 41,
"cellsInTier": 41,
"sampled": false,
"clean": 29,
"fabReady": 29,
"closureRate": 0.707,
"computeMinutes": 75.3,
"wallMinutes": 19.5,
"speedup": 3.9,
"workers": 4,
"summary": "29/41 fab-ready (12 built-not-ready, 0 crashed) \u2014 75 min of compute in 19 min of waiting, 3.9x on 4 workers",
"knownUnsupported": {
"usb-c-data + usb-c-power": "usb-c-data is a superset of usb-c-power and reuses the same refdes block (J1/R1/R2/U1/C1). Two USB-C entries on one board is a design error, not a layout problem \u2014 circuitlib.blocks says so in the usb-c-power notes, and helpers.board_plan never picks both."
},
"cells": [
{
"cell": [
"i2c-bus",
"ldo-3v3"
],
"blocks": 2,
"seconds": 90.7,
"boardMm": [
37.0,
17.6
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 5,
"blocking": [],
"warningCount": 83
},
{
"cell": [
"i2c-bus",
"rp2040-core"
],
"blocks": 2,
"seconds": 140.4,
"boardMm": [
53.9,
32.5
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
1
],
"bomLines": 24,
"blocking": [
{
"kind": "review_debug_unreachable",
"part": "board",
"detail": "the debug interface (SWCLK, SWD) reaches no connector or test point, so the board cannot be programmed or halted once it is assembled"
},
{
"kind": "drc_violation",
"part": "U3",
"detail": "[clearance] Clearance violation ( clearance 0.0900 mm; actual 0.0783 mm)"
}
],
"warningCount": 316
},
{
"cell": [
"i2c-bus",
"sensor-bme280"
],
"blocks": 2,
"seconds": 90.7,
"boardMm": [
34.0,
10.4
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 5,
"blocking": [],
"warningCount": 85
},
{
"cell": [
"i2c-bus",
"status-led"
],
"blocks": 2,
"seconds": 90.7,
"boardMm": [
29.2,
11.6
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 4,
"blocking": [],
"warningCount": 61
},
{
"cell": [
"i2c-bus",
"sw-tact"
],
"blocks": 2,
"seconds": 89.7,
"boardMm": [
33.4,
12.5
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 3,
"blocking": [],
"warningCount": 45
},
{
"cell": [
"i2c-bus",
"usb-c-data"
],
"blocks": 2,
"seconds": 101.0,
"boardMm": [
36.0,
27.6
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 9,
"blocking": [],
"warningCount": 133
},
{
"cell": [
"i2c-bus",
"usb-c-power"
],
"blocks": 2,
"seconds": 96.3,
"boardMm": [
34.2,
22.1
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 7,
"blocking": [],
"warningCount": 112
},
{
"cell": [
"i2c-bus",
"ws2812-chain"
],
"blocks": 2,
"seconds": 97.7,
"boardMm": [
58.4,
14.3
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 11,
"blocking": [],
"warningCount": 128
},
{
"cell": [
"ldo-3v3",
"rp2040-core"
],
"blocks": 2,
"seconds": 171.1,
"boardMm": [
61.0,
32.5
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
1
],
"bomLines": 25,
"blocking": [
{
"kind": "review_debug_unreachable",
"part": "board",
"detail": "the debug interface (SWCLK, SWD) reaches no connector or test point, so the board cannot be programmed or halted once it is assembled"
},
{
"kind": "drc_violation",
"part": "C6",
"detail": "[clearance] Clearance violation ( clearance 0.0900 mm; actual 0.0633 mm)"
}
],
"warningCount": 342
},
{
"cell": [
"ldo-3v3",
"sensor-bme280"
],
"blocks": 2,
"seconds": 88.8,
"boardMm": [
41.0,
17.6
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 6,
"blocking": [],
"warningCount": 112
},
{
"cell": [
"ldo-3v3",
"status-led"
],
"blocks": 2,
"seconds": 87.2,
"boardMm": [
36.3,
17.6
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 5,
"blocking": [],
"warningCount": 84
},
{
"cell": [
"ldo-3v3",
"sw-tact"
],
"blocks": 2,
"seconds": 84.2,
"boardMm": [
40.4,
17.6
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 4,
"blocking": [],
"warningCount": 73
},
{
"cell": [
"ldo-3v3",
"usb-c-data"
],
"blocks": 2,
"seconds": 98.5,
"boardMm": [
36.0,
36.5
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 10,
"blocking": [],
"warningCount": 153
},
{
"cell": [
"ldo-3v3",
"usb-c-power"
],
"blocks": 2,
"seconds": 95.2,
"boardMm": [
34.2,
31.0
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 8,
"blocking": [],
"warningCount": 132
},
{
"cell": [
"ldo-3v3",
"ws2812-chain"
],
"blocks": 2,
"seconds": 101.2,
"boardMm": [
65.5,
17.6
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 12,
"blocking": [],
"warningCount": 152
},
{
"cell": [
"rp2040-core",
"sensor-bme280"
],
"blocks": 2,
"seconds": 151.0,
"boardMm": [
57.9,
32.5
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
1
],
"bomLines": 25,
"blocking": [
{
"kind": "review_debug_unreachable",
"part": "board",
"detail": "the debug interface (SWCLK, SWD) reaches no connector or test point, so the board cannot be programmed or halted once it is assembled"
}
],
"warningCount": 324
},
{
"cell": [
"rp2040-core",
"status-led"
],
"blocks": 2,
"seconds": 116.3,
"boardMm": [
53.2,
32.5
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
1
],
"bomLines": 24,
"blocking": [
{
"kind": "review_debug_unreachable",
"part": "board",
"detail": "the debug interface (SWCLK, SWD) reaches no connector or test point, so the board cannot be programmed or halted once it is assembled"
}
],
"warningCount": 304
},
{
"cell": [
"rp2040-core",
"sw-tact"
],
"blocks": 2,
"seconds": 119.7,
"boardMm": [
57.4,
32.5
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
2
],
"bomLines": 23,
"blocking": [
{
"kind": "review_debug_unreachable",
"part": "board",
"detail": "the debug interface (SWCLK, SWD) reaches no connector or test point, so the board cannot be programmed or halted once it is assembled"
}
],
"warningCount": 301
},
{
"cell": [
"rp2040-core",
"usb-c-data"
],
"blocks": 2,
"seconds": 214.9,
"boardMm": [
48.4,
51.4
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
2,
2
],
"bomLines": 29,
"blocking": [
{
"kind": "dfm_hole_clearance",
"part": "U4",
"detail": "a pad passes 0.063mm from a via at (7.49, 11.50); the fab needs 0.2mm \u2014 route around it, the drill's own tolerance can cut a track this close"
},
{
"kind": "review_debug_unreachable",
"part": "board",
"detail": "the debug interface (SWCLK, SWD) reaches no connector or test point, so the board cannot be programmed or halted once it is assembled"
}
],
"warningCount": 378
},
{
"cell": [
"rp2040-core",
"usb-c-power"
],
"blocks": 2,
"seconds": 186.0,
"boardMm": [
48.4,
45.9
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
26,
26
],
"bomLines": 27,
"blocking": [
{
"kind": "pcb_trace_error",
"part": "board",
"detail": "Trace too close to board edge (0.210mm < 0.300mm required, margin: 0.2mm)"
},
{
"kind": "pcb_trace_error",
"part": "board",
"detail": "Trace too close to board edge (0.055mm < 0.300mm required, margin: 0.2mm)"
},
{
"kind": "pcb_trace_error",
"part": "board",
"detail": "Trace too close to board edge (0.000mm < 0.300mm required, margin: 0.2mm)"
},
{
"kind": "pcb_trace_error",
"part": "board",
"detail": "Trace too close to board edge (0.092mm < 0.300mm required, margin: 0.2mm)"
},
{
"kind": "pcb_trace_error",
"part": "board",
"detail": "Trace too close to board edge (0.103mm < 0.300mm required, margin: 0.2mm)"
},
{
"kind": "pcb_placement_error",
"part": "board",
"detail": "Via pcb_via[#pcb_via_42] is outside or crossing the board boundary"
},
{
"kind": "pcb_placement_error",
"part": "board",
"detail": "Via pcb_via[#pcb_via_43] is outside or crossing the board boundary"
},
{
"kind": "pcb_placement_error",
"part": "R12.pin2",
"detail": "Via at (-9.76mm, 6.37mm) is inside SMD pad R12.pin2 at (-9.76mm, 6.25mm)"
},
{
"kind": "dfm_edge_clearance",
"part": "board",
"detail": "copper is -0.392mm from the board edge (fab minimum 0.2mm)"
},
{
"kind": "dfm_edge_clearance",
"part": "board",
"detail": "copper is -0.862mm from the board edge (fab minimum 0.2mm)"
},
{
"kind": "review_debug_unreachable",
"part": "board",
"detail": "the debug interface (SWCLK, SWD) reaches no connector or test point, so the board cannot be programmed or halted once it is assembled"
},
{
"kind": "drc_violation",
"part": "Segment on Edge.Cuts",
"detail": "[copper_edge_clearance] Board edge clearance violation (board setup constraints edge clearance 0.1900 mm; actual 0.1101 mm)"
},
{
"kind": "drc_violation",
"part": "Segment on Edge.Cuts",
"detail": "[copper_edge_clearance] Board edge clearance violation (board setup constraints edge clearance 0.1900 mm; actual 0.0000 mm)"
},
{
"kind": "drc_violation",
"part": "Segment on Edge.Cuts",
"detail": "[copper_edge_clearance] Board edge clearance violation (board setup constraints edge clearance 0.1900 mm; actual 0.0030 mm)"
}
],
"warningCount": 374
},
{
"cell": [
"rp2040-core",
"ws2812-chain"
],
"blocks": 2,
"seconds": 169.7,
"boardMm": [
82.4,
32.5
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
3,
3
],
"bomLines": 31,
"blocking": [
{
"kind": "pcb_placement_error",
"part": "D12.DOUT",
"detail": "Via at (18.67mm, -0.75mm) is inside SMD pad D12.DOUT at (18.06mm, -0.75mm)"
},
{
"kind": "review_debug_unreachable",
"part": "board",
"detail": "the debug interface (SWCLK, SWD) reaches no connector or test point, so the board cannot be programmed or halted once it is assembled"
}
],
"warningCount": 375
},
{
"cell": [
"sensor-bme280",
"status-led"
],
"blocks": 2,
"seconds": 94.2,
"boardMm": [
33.2,
11.6
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 5,
"blocking": [],
"warningCount": 99
},
{
"cell": [
"sensor-bme280",
"sw-tact"
],
"blocks": 2,
"seconds": 91.2,
"boardMm": [
37.4,
12.5
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 4,
"blocking": [],
"warningCount": 84
},
{
"cell": [
"sensor-bme280",
"usb-c-data"
],
"blocks": 2,
"seconds": 135.8,
"boardMm": [
36.0,
29.3
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 10,
"blocking": [
{
"kind": "drc_violation",
"part": "Via [USB_DM_CONN] on F.Cu - B.Cu",
"detail": "[clearance] Clearance violation ( clearance 0.0900 mm; actual 0.0417 mm)"
},
{
"kind": "drc_violation",
"part": "J1",
"detail": "[hole_clearance] Hole clearance violation (board setup constraints hole clearance 0.2000 mm; actual 0.1917 mm)"
}
],
"warningCount": 164
},
{
"cell": [
"sensor-bme280",
"usb-c-power"
],
"blocks": 2,
"seconds": 110.4,
"boardMm": [
34.2,
23.8
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 8,
"blocking": [],
"warningCount": 141
},
{
"cell": [
"sensor-bme280",
"ws2812-chain"
],
"blocks": 2,
"seconds": 111.4,
"boardMm": [
62.4,
14.3
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 12,
"blocking": [],
"warningCount": 165
},
{
"cell": [
"status-led",
"sw-tact"
],
"blocks": 2,
"seconds": 99.9,
"boardMm": [
32.7,
12.5
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 3,
"blocking": [],
"warningCount": 52
},
{
"cell": [
"status-led",
"usb-c-data"
],
"blocks": 2,
"seconds": 103.3,
"boardMm": [
36.0,
30.5
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 9,
"blocking": [],
"warningCount": 138
},
{
"cell": [
"status-led",
"usb-c-power"
],
"blocks": 2,
"seconds": 100.9,
"boardMm": [
34.2,
25.0
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 7,
"blocking": [],
"warningCount": 114
},
{
"cell": [
"status-led",
"ws2812-chain"
],
"blocks": 2,
"seconds": 99.9,
"boardMm": [
57.7,
14.3
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 11,
"blocking": [],
"warningCount": 132
},
{
"cell": [
"sw-tact",
"usb-c-data"
],
"blocks": 2,
"seconds": 126.0,
"boardMm": [
36.0,
31.4
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
2,
2
],
"bomLines": 8,
"blocking": [
{
"kind": "pcb_trace_error",
"part": "J1",
"detail": "PCB trace trace[.J1 > port.GND1, .J1 > port.GND2] is too close to pcb_keepout \"pcb_keepout[#pcb_keepout_0]\" (gap: 0.078mm)"
},
{
"kind": "drc_violation",
"part": "J1",
"detail": "[clearance] Clearance violation ( clearance 0.0900 mm; actual 0.0679 mm)"
}
],
"warningCount": 117
},
{
"cell": [
"sw-tact",
"usb-c-power"
],
"blocks": 2,
"seconds": 92.4,
"boardMm": [
34.2,
25.9
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 6,
"blocking": [],
"warningCount": 91
},
{
"cell": [
"sw-tact",
"ws2812-chain"
],
"blocks": 2,
"seconds": 90.9,
"boardMm": [
61.9,
14.3
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 10,
"blocking": [],
"warningCount": 119
},
{
"cell": [
"usb-c-data",
"ws2812-chain"
],
"blocks": 2,
"seconds": 119.7,
"boardMm": [
52.9,
33.2
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
2,
2
],
"bomLines": 16,
"blocking": [
{
"kind": "pcb_trace_error",
"part": "J1",
"detail": "PCB trace trace[.J1 > port.GND1, .J1 > port.GND2] is too close to pcb_keepout \"pcb_keepout[#pcb_keepout_0]\" (gap: 0.078mm)"
},
{
"kind": "drc_violation",
"part": "V5",
"detail": "[clearance] Clearance violation ( clearance 0.0900 mm; actual 0.0535 mm)"
}
],
"warningCount": 212
},
{
"cell": [
"usb-c-power",
"ws2812-chain"
],
"blocks": 2,
"seconds": 92.0,
"boardMm": [
52.9,
27.7
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 14,
"blocking": [],
"warningCount": 188
},
{
"cell": [
"i2c-bus",
"ldo-3v3",
"usb-c-power"
],
"blocks": 3,
"seconds": 85.2,
"boardMm": [
37.0,
31.0
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 10,
"blocking": [],
"warningCount": 150
},
{
"cell": [
"ldo-3v3",
"rp2040-core",
"usb-c-power"
],
"blocks": 3,
"seconds": 146.2,
"boardMm": [
61.0,
45.9
],
"status": "blocked",
"fabReady": false,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 30,
"blocking": [
{
"kind": "review_debug_unreachable",
"part": "board",
"detail": "the debug interface (SWCLK, SWD) reaches no connector or test point, so the board cannot be programmed or halted once it is assembled"
}
],
"warningCount": 401
},
{
"cell": [
"ldo-3v3",
"sensor-bme280",
"usb-c-power"
],
"blocks": 3,
"seconds": 94.8,
"boardMm": [
41.0,
31.0
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 11,
"blocking": [],
"warningCount": 179
},
{
"cell": [
"ldo-3v3",
"status-led",
"usb-c-power"
],
"blocks": 3,
"seconds": 90.5,
"boardMm": [
36.3,
31.0
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 10,
"blocking": [],
"warningCount": 151
},
{
"cell": [
"ldo-3v3",
"sw-tact",
"usb-c-power"
],
"blocks": 3,
"seconds": 81.5,
"boardMm": [
40.4,
31.0
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 9,
"blocking": [],
"warningCount": 140
},
{
"cell": [
"ldo-3v3",
"usb-c-power",
"ws2812-chain"
],
"blocks": 3,
"seconds": 69.3,
"boardMm": [
65.5,
31.0
],
"status": "clean",
"fabReady": true,
"autorouterEffort": "default",
"blockingByAttempt": [
0
],
"bomLines": 17,
"blocking": [],
"warningCount": 226
}
]
}
26e259c5cThis file is pinned to the selected release. Download the original to open it in your design tool.