aes

//======================================================================
//
// aes_decipher_block.v
// --------------------
// The AES decipher round. A pure combinational module that implements
// the initial round, main round and final round logic for
// decciper operations.
//
//
// Author: Joachim Strombergson
// Copyright (c) 2013, 2014, Secworks Sweden AB
// All rights reserved.
//
// Redistribution and use in source and binary forms, with or
// without modification, are permitted provided that the following
// conditions are met:
//
// 1. Redistributions of source code must retain the above copyright
//    notice, this list of conditions and the following disclaimer.
//
// 2. Redistributions in binary form must reproduce the above copyright
//    notice, this list of conditions and the following disclaimer in
//    the documentation and/or other materials provided with the
//    distribution.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
// FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
// COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
// INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
// BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
// LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
// CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
// STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
// ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
//======================================================================

module aes_decipher_block(
                          input wire            clk,
                          input wire            reset_n,

                          input wire            next,

                          input wire            keylen,
                          output wire [3 : 0]   round,
                          input wire [127 : 0]  round_key,

                          input wire [127 : 0]  block,
                          output wire [127 : 0] new_block,
                          output wire           ready
                         );


  //----------------------------------------------------------------
  // Internal constant and parameter definitions.
  //----------------------------------------------------------------
  localparam AES_128_BIT_KEY = 1'h0;
  localparam AES_256_BIT_KEY = 1'h1;

  localparam AES128_ROUNDS = 4'ha;
  localparam AES256_ROUNDS = 4'he;

  localparam NO_UPDATE    = 3'h0;
  localparam INIT_UPDATE  = 3'h1;
  localparam SBOX_UPDATE  = 3'h2;
  localparam MAIN_UPDATE  = 3'h3;
  localparam FINAL_UPDATE = 3'h4;

  localparam CTRL_IDLE  = 3'h0;
  localparam CTRL_INIT  = 3'h1;
  localparam CTRL_SBOX  = 3'h2;
  localparam CTRL_MAIN  = 3'h3;
  localparam CTRL_FINAL = 3'h4;


  //----------------------------------------------------------------
  // Gaolis multiplication functions for Inverse MixColumn.
  //----------------------------------------------------------------
  function [7 : 0] gm2(input [7 : 0] op);
    begin
      gm2 = {op[6 : 0], 1'b0} ^ (8'h1b & {8{op[7]}});
    end
  endfunction // gm2

  function [7 : 0] gm3(input [7 : 0] op);
    begin
      gm3 = gm2(op) ^ op;
    end
  endfunction // gm3

  function [7 : 0] gm4(input [7 : 0] op);
    begin
      gm4 = gm2(gm2(op));
    end
  endfunction // gm4

  function [7 : 0] gm8(input [7 : 0] op);
    begin
      gm8 = gm2(gm4(op));
    end
  endfunction // gm8

  function [7 : 0] gm09(input [7 : 0] op);
    begin
      gm09 = gm8(op) ^ op;
    end
  endfunction // gm09

  function [7 : 0] gm11(input [7 : 0] op);
    begin
      gm11 = gm8(op) ^ gm2(op) ^ op;
    end
  endfunction // gm11

  function [7 : 0] gm13(input [7 : 0] op);
    begin
      gm13 = gm8(op) ^ gm4(op) ^ op;
    end
  endfunction // gm13

  function [7 : 0] gm14(input [7 : 0] op);
    begin
      gm14 = gm8(op) ^ gm4(op) ^ gm2(op);
    end
  endfunction // gm14

  function [31 : 0] inv_mixw(input [31 : 0] w);
    reg [7 : 0] b0, b1, b2, b3;
    reg [7 : 0] mb0, mb1, mb2, mb3;
    begin
      b0 = w[31 : 24];
      b1 = w[23 : 16];
      b2 = w[15 : 08];
      b3 = w[07 : 00];

      mb0 = gm14(b0) ^ gm11(b1) ^ gm13(b2) ^ gm09(b3);
      mb1 = gm09(b0) ^ gm14(b1) ^ gm11(b2) ^ gm13(b3);
      mb2 = gm13(b0) ^ gm09(b1) ^ gm14(b2) ^ gm11(b3);
      mb3 = gm11(b0) ^ gm13(b1) ^ gm09(b2) ^ gm14(b3);

      inv_mixw = {mb0, mb1, mb2, mb3};
    end
  endfunction // mixw

  function [127 : 0] inv_mixcolumns(input [127 : 0] data);
    reg [31 : 0] w0, w1, w2, w3;
    reg [31 : 0] ws0, ws1, ws2, ws3;
    begin
      w0 = data[127 : 096];
      w1 = data[095 : 064];
      w2 = data[063 : 032];
      w3 = data[031 : 000];

      ws0 = inv_mixw(w0);
      ws1 = inv_mixw(w1);
      ws2 = inv_mixw(w2);
      ws3 = inv_mixw(w3);

      inv_mixcolumns = {ws0, ws1, ws2, ws3};
    end
  endfunction // inv_mixcolumns

  function [127 : 0] inv_shiftrows(input [127 : 0] data);
    reg [31 : 0] w0, w1, w2, w3;
    reg [31 : 0] ws0, ws1, ws2, ws3;
    begin
      w0 = data[127 : 096];
      w1 = data[095 : 064];
      w2 = data[063 : 032];
      w3 = data[031 : 000];

      ws0 = {w0[31 : 24], w3[23 : 16], w2[15 : 08], w1[07 : 00]};
      ws1 = {w1[31 : 24], w0[23 : 16], w3[15 : 08], w2[07 : 00]};
      ws2 = {w2[31 : 24], w1[23 : 16], w0[15 : 08], w3[07 : 00]};
      ws3 = {w3[31 : 24], w2[23 : 16], w1[15 : 08], w0[07 : 00]};

      inv_shiftrows = {ws0, ws1, ws2, ws3};
    end
  endfunction // inv_shiftrows

  function [127 : 0] addroundkey(input [127 : 0] data, input [127 : 0] rkey);
    begin
      addroundkey = data ^ rkey;
    end
  endfunction // addroundkey


  //----------------------------------------------------------------
  // Registers including update variables and write enable.
  //----------------------------------------------------------------
  reg [1 : 0]   sword_ctr_reg;
  reg [1 : 0]   sword_ctr_new;
  reg           sword_ctr_we;
  reg           sword_ctr_inc;
  reg           sword_ctr_rst;

  reg [3 : 0]   round_ctr_reg;
  reg [3 : 0]   round_ctr_new;
  reg           round_ctr_we;
  reg           round_ctr_set;
  reg           round_ctr_dec;

  reg [127 : 0] block_new;
  reg [31 : 0]  block_w0_reg;
  reg [31 : 0]  block_w1_reg;
  reg [31 : 0]  block_w2_reg;
  reg [31 : 0]  block_w3_reg;
  reg           block_w0_we;
  reg           block_w1_we;
  reg           block_w2_we;
  reg           block_w3_we;

  reg           ready_reg;
  reg           ready_new;
  reg           ready_we;

  reg [2 : 0]   dec_ctrl_reg;
  reg [2 : 0]   dec_ctrl_new;
  reg           dec_ctrl_we;


  //----------------------------------------------------------------
  // Wires.
  //----------------------------------------------------------------
  reg [31 : 0]  tmp_sboxw;
  wire [31 : 0] new_sboxw;
  reg [2 : 0]   update_type;


  //----------------------------------------------------------------
  // Instantiations.
  //----------------------------------------------------------------
  aes_inv_sbox inv_sbox_inst(.sword(tmp_sboxw), .new_sword(new_sboxw));


  //----------------------------------------------------------------
  // Concurrent connectivity for ports etc.
  //----------------------------------------------------------------
  assign round     = round_ctr_reg;
  assign new_block = {block_w0_reg, block_w1_reg, block_w2_reg, block_w3_reg};
  assign ready     = ready_reg;


  //----------------------------------------------------------------
  // reg_update
  //
  // Update functionality for all registers in the core.
  // All registers are positive edge triggered with synchronous
  // active low reset. All registers have write enable.
  //----------------------------------------------------------------
  always @ (posedge clk or negedge reset_n)
    begin: reg_update
      if (!reset_n)
        begin
          block_w0_reg  <= 32'h0;
          block_w1_reg  <= 32'h0;
          block_w2_reg  <= 32'h0;
          block_w3_reg  <= 32'h0;
          sword_ctr_reg <= 2'h0;
          round_ctr_reg <= 4'h0;
          ready_reg     <= 1'b1;
          dec_ctrl_reg  <= CTRL_IDLE;
        end
      else
        begin
          if (block_w0_we)
            block_w0_reg <= block_new[127 : 096];

          if (block_w1_we)
            block_w1_reg <= block_new[095 : 064];

          if (block_w2_we)
            block_w2_reg <= block_new[063 : 032];

          if (block_w3_we)
            block_w3_reg <= block_new[031 : 000];

          if (sword_ctr_we)
            sword_ctr_reg <= sword_ctr_new;

          if (round_ctr_we)
            round_ctr_reg <= round_ctr_new;

          if (ready_we)
            ready_reg <= ready_new;

          if (dec_ctrl_we)
            dec_ctrl_reg <= dec_ctrl_new;
        end
    end // reg_update


  //----------------------------------------------------------------
  // round_logic
  //
  // The logic needed to implement init, main and final rounds.
  //----------------------------------------------------------------
  always @*
    begin : round_logic
      reg [127 : 0] old_block, inv_shiftrows_block, inv_mixcolumns_block;
      reg [127 : 0] addkey_block;

      inv_shiftrows_block  = 128'h0;
      inv_mixcolumns_block = 128'h0;
      addkey_block         = 128'h0;
      block_new            = 128'h0;
      tmp_sboxw            = 32'h0;
      block_w0_we          = 1'b0;
      block_w1_we          = 1'b0;
      block_w2_we          = 1'b0;
      block_w3_we          = 1'b0;

      old_block            = {block_w0_reg, block_w1_reg, block_w2_reg, block_w3_reg};

      // Update based on update type.
      case (update_type)
        // InitRound
        INIT_UPDATE:
          begin
            old_block           = block;
            addkey_block        = addroundkey(old_block, round_key);
            inv_shiftrows_block = inv_shiftrows(addkey_block);
            block_new           = inv_shiftrows_block;
            block_w0_we         = 1'b1;
            block_w1_we         = 1'b1;
            block_w2_we         = 1'b1;
            block_w3_we         = 1'b1;
          end

        SBOX_UPDATE:
          begin
            block_new = {new_sboxw, new_sboxw, new_sboxw, new_sboxw};

            case (sword_ctr_reg)
              2'h0:
                begin
                  tmp_sboxw   = block_w0_reg;
                  block_w0_we = 1'b1;
                end

              2'h1:
                begin
                  tmp_sboxw   = block_w1_reg;
                  block_w1_we = 1'b1;
                end

              2'h2:
                begin
                  tmp_sboxw   = block_w2_reg;
                  block_w2_we = 1'b1;
                end

              2'h3:
                begin
                  tmp_sboxw   = block_w3_reg;
                  block_w3_we = 1'b1;
                end
            endcase // case (sbox_mux_ctrl_reg)
          end

        MAIN_UPDATE:
          begin
            addkey_block         = addroundkey(old_block, round_key);
            inv_mixcolumns_block = inv_mixcolumns(addkey_block);
            inv_shiftrows_block  = inv_shiftrows(inv_mixcolumns_block);
            block_new            = inv_shiftrows_block;
            block_w0_we          = 1'b1;
            block_w1_we          = 1'b1;
            block_w2_we          = 1'b1;
            block_w3_we          = 1'b1;
          end

        FINAL_UPDATE:
          begin
            block_new    = addroundkey(old_block, round_key);
            block_w0_we  = 1'b1;
            block_w1_we  = 1'b1;
            block_w2_we  = 1'b1;
            block_w3_we  = 1'b1;
          end

        default:
          begin
          end
      endcase // case (update_type)
    end // round_logic


  //----------------------------------------------------------------
  // sword_ctr
  //
  // The subbytes word counter with reset and increase logic.
  //----------------------------------------------------------------
  always @*
    begin : sword_ctr
      sword_ctr_new = 2'h0;
      sword_ctr_we  = 1'b0;

      if (sword_ctr_rst)
        begin
          sword_ctr_new = 2'h0;
          sword_ctr_we  = 1'b1;
        end
      else if (sword_ctr_inc)
        begin
          sword_ctr_new = sword_ctr_reg + 1'b1;
          sword_ctr_we  = 1'b1;
        end
    end // sword_ctr


  //----------------------------------------------------------------
  // round_ctr
  //
  // The round counter with reset and increase logic.
  //----------------------------------------------------------------
  always @*
    begin : round_ctr
      round_ctr_new = 4'h0;
      round_ctr_we  = 1'b0;

      if (round_ctr_set)
        begin
          if (keylen == AES_256_BIT_KEY)
            begin
              round_ctr_new = AES256_ROUNDS;
            end
          else
            begin
              round_ctr_new = AES128_ROUNDS;
            end
          round_ctr_we  = 1'b1;
        end
      else if (round_ctr_dec)
        begin
          round_ctr_new = round_ctr_reg - 1'b1;
          round_ctr_we  = 1'b1;
        end
    end // round_ctr


  //----------------------------------------------------------------
  // decipher_ctrl
  //
  // The FSM that controls the decipher operations.
  //----------------------------------------------------------------
  always @*
    begin: decipher_ctrl
      sword_ctr_inc = 1'b0;
      sword_ctr_rst = 1'b0;
      round_ctr_dec = 1'b0;
      round_ctr_set = 1'b0;
      ready_new     = 1'b0;
      ready_we      = 1'b0;
      update_type   = NO_UPDATE;
      dec_ctrl_new  = CTRL_IDLE;
      dec_ctrl_we   = 1'b0;

      case(dec_ctrl_reg)
        CTRL_IDLE:
          begin
            if (next)
              begin
                round_ctr_set = 1'b1;
                ready_new     = 1'b0;
                ready_we      = 1'b1;
                dec_ctrl_new  = CTRL_INIT;
                dec_ctrl_we   = 1'b1;
              end
          end

        CTRL_INIT:
          begin
            sword_ctr_rst = 1'b1;
            update_type   = INIT_UPDATE;
            dec_ctrl_new  = CTRL_SBOX;
            dec_ctrl_we   = 1'b1;
          end

        CTRL_SBOX:
          begin
            sword_ctr_inc = 1'b1;
            update_type   = SBOX_UPDATE;
            if (sword_ctr_reg == 2'h3)
              begin
                round_ctr_dec = 1'b1;
                dec_ctrl_new  = CTRL_MAIN;
                dec_ctrl_we   = 1'b1;
              end
          end

        CTRL_MAIN:
          begin
            sword_ctr_rst = 1'b1;
            if (round_ctr_reg > 0)
              begin
                update_type   = MAIN_UPDATE;
                dec_ctrl_new  = CTRL_SBOX;
                dec_ctrl_we   = 1'b1;
              end
            else
              begin
                update_type  = FINAL_UPDATE;
                ready_new    = 1'b1;
                ready_we     = 1'b1;
                dec_ctrl_new = CTRL_IDLE;
                dec_ctrl_we  = 1'b1;
              end
          end

        default:
          begin
            // Empty. Just here to make the synthesis tool happy.
          end
      endcase // case (dec_ctrl_reg)
    end // decipher_ctrl

endmodule // aes_decipher_block

//======================================================================
// EOF aes_decipher_block.v
//======================================================================